- Joined
- Apr 1, 2020
- Messages
- 94
- Motherboard
- Gigabyte Z390 Designare
- CPU
- i9-9900K
- Graphics
- RX 580
Confirmed. Booted up right now.Remind me please if Clover can boot the exact same disk that you are trying to boot using OpenCore.
Confirmed. Booted up right now.Remind me please if Clover can boot the exact same disk that you are trying to boot using OpenCore.
I'd like to compare the Clover and OpenCore folders to see if there's a clue to be found. If you can make a copy of both folders, remove serial numbers from each config.plist, compress and post the zip, I'll take a closer look.Confirmed. Booted up right now.
We have had this problem with NVM50 on Z490 Vision D since the beginning. No solution has been found. Have you tried this one?@CaseySJ
I have tried some UFEI FW´s for my Z620, without success.
But I don't think that this problem is related to some similar of the 9j FW.
HP has not updated the FW for modern AMG Graphics e.g. resizable BAR.
And there are even no Intel hot fixes of 2020.
It look like, the USB-C Ports cannot be set in the right state because of something is missing or have to patch via DSDT/SSDT. But I have no idea what. See picture.
With original firmware, please disable the Thunderbolt SSDT, boot macOS and run IORegistryExplorer --> File --> Save As... and post the IOReg file.By the way: If I use the original Firewire FW, the card will not recognized by MacOS.
Yes, I have tried the DESIGNARE-Z390-NVM33-Elias64Fr.bin, the same error.We have had this problem with NVM50 on Z490 Vision D since the beginning. No solution has been found. Have you tried this one?
- DESIGNARE-Z390-NVM33-Elias64Fr.bin
With original firmware, please disable the Thunderbolt SSDT, boot macOS and run IORegistryExplorer --> File --> Save As... and post the IOReg file.
MacOS will scan the PCI bus and will discover all devices even without SSDT. By looking at this new IOReg file we can see exactly what macOS has detected.
Okay Ok so interestingly enough. Safe boot seems to cure the freezing?OkIt's super strange I ran into once during Catalina Betas. I'm going to try a fresh install tonight to see if that does it, maybe some old kext conflicts or something. Just glad to know it's just me so it can be fixed.
Attached. Labeled each folder w/ Clover and 066(OC).I'd like to compare the Clover and OpenCore folders to see if there's a clue to be found. If you can make a copy of both folders, remove serial numbers from each config.plist, compress and post the zip, I'll take a closer look.
One difference between the two is the presence of an SSDT in Clover to disable GPU in Slot 2. If there's an Nvidia GPU in that slot, please do the following:Attached. Labeled each folder w/ Clover and 066(OC).
That is very puzzling. With the original firmware installed and no Thunderbolt SSDT, please run Hackintool and click the Export button as shown:Yes, I have tried the DESIGNARE-Z390-NVM33-Elias64Fr.bin, the same error.
With the original FW, there is nothing. Not in IOReg, not in the PCI list of Hackintool. The Card is not present, I have tried it twice with reflash. With DSDT and without, with Jumper between 1-3 and 1-4 and without.
Like the USB-C Controller if I reboot, just gone.
Yes only the blue chip.Edit: Wait, I have flash only the blue Chip, is this correct?
The green chip contains Thunderbolt Power Delivery (PD) firmware. Remember that Thunderbolt connectors also support up to 100W of power delivery to connected components. This is managed by a Texas Instruments power delivery chip.Because on my cMP5.1 this Card is working but I have to flash both chips.
I don't know, what FW is on the green one, maybe NVM50.