Sure. I don't need to upload anything. I will just tell, what I have.
So first the bios settings. See the pictures I uploaded.
Yes I have ga-z68-ud5-b3 on F10 bios.
My org.chameleon.Boot.plist:
"
<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd">
<plist version="1.0">
<dict>
<key>Quiet Boot</key>
<string>Yes</string>
<key>Boot Banner</key>
<string>No</string>
<key>EthernetBuiltIn</key>
<string>Yes</string>
<key>GenerateCStates</key>
<string>Yes</string>
<key>GeneratePStates</key>
<string>Yes</string>
<key>Graphics Mode</key>
<string>1920x1080x32</string>
<key>GraphicsEnabler</key>
<string>Yes</string>
<key>Kernel</key>
<string>mach_kernel</string>
<key>Kernel Flags</key>
<string>npci=0x3000 darkwake=1</string>
<key>UseKernelCache</key>
<string>Yes</string>
</dict>
</plist>
"
I have a custom DSDT based on the macman's dsdt plus some patches for internal SATA Drivers.
Then I have a self made SSDT. It won't work, because I have iMac12,2 as definition and I just have 16x and 44x. It doesn't bother me. There is a fix for it, but I dont need it.
my smbios.plist:
"
<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd">
<plist version="1.0">
<dict>
<key>SMfamily</key>
<string>iMac</string>
<key>SMproductname</key>
<string>iMac12,2</string>
<key>SMboardproduct</key>
<string>Mac-942B59F58194171B</string>
<key>SMserial</key>
<string>C02FT7U2DHJP</string>
<key>SMbiosversion</key>
<string>MultiBeast.tonymacx86.com</string>
</dict>
</plist>
"
After clean ML install I just installed from multibeast 4.6.1 only following:
- Chimera
- Patched AppleHDA->ALC889
- Lnx2Mac's Realtek drivers
- trim enabler (for my ssd)
And I have only the following kexts:
- AppleHDA.kext (from Multibeast) needed for sound
- AppleRTC.kext (self patched, search for my post about it) needed for CMOS reset after reboot
- FakeSMC.kext (from HWMonitor git) needed
- IntelThermal.kext (from HWMonitor git) dont needed but good for thermal readings
- NouveauSensors.kext (from HWMonitor git) dont needed but good for thermal readings
- RealtekRTL81xx.kext (from Multibeast) needed for Ethernet
- SuperIOSensors.kext (from HWMonitor git) dont needed but good for thermal readings
And most importantly no NullIntelCPU crap...
For Lion I had a EFI for my SLI graphics and Ethernet (for appstore), but in ML I don't need them.
You know what, there you go. I uploaded all my kexts and my Extra folder. Be careful after extracting. Do chmod -R root:wheel * on kexts and after installing them run following:
"sudo kextcache -system-prelinked-kernel; sudo kextcache -system-caches"