Booting without cpus=1 results freeze at FIPS USER Space POST Success!

[diebolo]

Well, Booting without the boot flag cpus=1 will result in a stuck screen

• -v: After:

  DYLIB_FIPS_POST: FIPS USER Space POST Success!

  it gets stuck (See photo).
• Boot flags that I use: kernel-dev-mode=1 dart=0 nv_disable=1
• I followed RehabMan's guide of Native power management for laptop's but I don't know how to verify success of this guide.
• Nvidia Web Driver installed but nvda_drv=1 will result in the same situation
• With the boot flag cpus=1 it just completely boots up and fully work. Except the GPU is not detected in the ECC of the Nvidia driver panel.
• The laptop is going to be used for Vectorworks, a architect proram, so all 4 cores and a GPU would be nice.

Sincerely,
Dielof

 

[RehabMan]

Well, Booting without the boot flag cpus=1 will result in a stuck screen

• -v: After: it gets stuck (See photo).
• Boot flags that I use: kernel-dev-mode=1 dart=0 nv_disable=1
• I followed RehabMan's guide of Native power management for laptop's but I don't know how to verify success of this guide.
• Nvidia Web Driver installed but nvda_drv=1 will result in the same situation
• With the boot flag cpus=1 it just completely boots up and fully work. Except the GPU is not detected in the ECC of the Nvidia driver panel.
• The laptop is going to be used for Vectorworks, a architect proram, so all 4 cores and a GPU would be nice.

Sincerely,
DielofView attachment 225375

Attach EFI/Clover folder as ZIP (omit 'themes' folder).
Attach output of 'lspci -nn' in Linux Terminal.

 

[diebolo]

Attach EFI/Clover folder as ZIP (omit 'themes' folder).
Attach output of 'lspci -nn' in Linux Terminal.

Attached the Clover.
But how can I possibly install (Kali) Linux while there is OSX on my SSD?

 

[RehabMan]

Attached the Clover.
But how can I possibly install (Kali) Linux while there is OSX on my SSD?

Linux can be run directly from USB.

 

[diebolo]

Linux can be run directly from USB.

• I couldn't get Kali Linux (live) to run lspci. It just freezed the terminal (tried 3 times)
• Tried Fedora, which didn't boot
• Tried Puppy Linux (idk)
• Tried ubuntu: I couldn't get the live version working so this is lspci output from grub (couldn't put -nn in, hope it still works):

grub> lspci
00:00.0 8066:1910 [0600] Host Bridge
00:01.0 8086:1901 [0604] PCI-PCI Bridge
00:02.0 8086:191b [0300] VGA Controller
00:14.0 8086:a12f [0c03] LISB Controller [PI 30]
00:14.2 8086:a131 [1180] Unknown Data Input System
00:16.0 8086:a13a [0780] Communication controller
00:17.0 8086:a103 [0106] SATA Controller [PI 01]
00:1e.0 8086:a110 [0604] PCI-PCI Bridge
00:1c.3 8086:a113 [0604] PCI-PCI Bridge
00:1f.0 8086:a14e [0601] ISA Bridge
00:1f.2 8086:a121 [0580] Memory Controller
00:1f.3 8086:a170 [0403] Multimedia device
00:1f.4 8086:a123 [0c05] Serial Bus Controller
01:00.0 10de:139b [0302] 3D Controller
02:00.0 8086:3165 [0280] Network controller
03:00.0 1969:e0a1 [0200] Ethernet Controller

 

[RehabMan]

Attached the Clover.
But how can I possibly install (Kali) Linux while there is OSX on my SSD?

Follow the Clover guide linked from the FAQ.

http://www.tonymacx86.com/el-capita...faq-read-first-laptop-frequent-questions.html

Pay attention the Skylake info in the FAQ. It is important.