cpus=1

Hello, I just got High Sierra up and running on my new machine, however I've run into a major issue, which is that my system seems not to be stable unless I use the boot flag cpus=6 (or 1-5). Above 6, or without the flag, the computer will restart after about 30 seconds of being logged in. I...

So ive been trying to just get to the installer for this bloody thing. First off it only starts to boot in safe mode or I get error loading kernel cache then boot failed. But when i use safe mode it gets to the photo below. cpus=1 changes nothing it still gets stuck at the same part. I tried...

So I've gotten 10.13.3 mostly installed, but I can't for the life of me get it running stable with my CPU. The only way I can get it to boot is with some variation of "cpus=". Usually I can boot with cpus=1, but only have one cpu thread active. Sometimes, however, I can boot with cpus=10 and at...

So I've gotten High Sierra mostly up and running. The one issue I can't seem to figure out is how to utilize all 6 cpu cores. I can't boot without cpus=1 hince why I can only utilize 1 core. I installed with clover, but have also tried installing multibeasts 6-core cpu driver with no luck. If I...

I have installed mac 10.12.6 on (lenovo ideapad 510-15ikb) but with no hardware working properly -_- but the most important thing is intel 620 HD graphics cause huge problem in display no thing work smoothly also, i can only boot with cpus=1 which make my cpu as flying copter, i have tried...

Hi, My Hackintosh with Sierra worked perfectly with the support from the forum and specially @P1LGRIM. However, I had multiple boot entries for the UEFI partition for the Hackintosh boot drive which were increasing with every boot. After reading somewhere, I decided to update the BIOS for my...

Hi! Sierra 10.12.5 works (Graphics accelerated, audio and USBs working) but still need cpus=4 to not getting restarted after minutes of using the hackintosh. EFI Folder attached. I search for other similar threads but are old and relative to Mavericks and El Capitan. Also don´t know how to...

Hi, I got a strange problem with macOS installation. Both installation and system boots only with cpus=1. I tried both Voodoo and NullCPU, tried various BIOS settings configurations, various other boot flags. Nothing helps. -- -- -- Some info about my PC: Model: MSI PE60 6QE Motherboard...

All system works good on one core, but it's just one, not four)) Can someone help me with my problem All information in BugReport CPU: Intel Core-i5 2300 MacOS 10.12.4 Anonymous UUID: 03DEDB97-7DDA-68B3-115E-A8AFDDC49053 Thu Jun 1 19:02:59 2017 *** Panic Report *** panic(cpu 2 caller...

Hello, I have successfully installed Sierra on my MSI Notebook alongside Windows 10. I'm blown away by the fact that I have set my smbios to MacBook 13,3 (and it works) but my computer will not boot without cpus=1. I know this has been an issue for others, and I have tried all the fixes I could...

Well, Booting without the boot flag cpus=1 will result in a stuck screen -v: After: it gets stuck (See photo). Boot flags that I use: kernel-dev-mode=1 dart=0 nv_disable=1 I followed RehabMan's guide of Native power management for laptop's but I don't know how to verify success of this guide...

Hey! I recently set up a Hackintosh but required cpus=1 to boot. Because of that (and that cpus=1 only lets you use 1 CPU), I installed NullCPUPowerManagement and can report success removing the flag except for a few problems: VoodooHDA works but my audio device isn't recognised and Clover...

Hey guys, I hope you can help me out. I've sucessfully installed El Capitan using Clover with cpus=1. I can boot into OS X with cpus=1, too, but I want all 2 cores to be supported and do not know how to do that. I have never used Clover and the last time on Mavericks i used something called...

Let me start by saying that I tried to fix this without starting a new thread, but I suck, so here is a new thread. First off, I had a fully functional Hackintosh for the past 5 years. It was stable and I was running Mavericks. Then I decided to upgrade my graphics card to the Evga gtx 980 ti...

I built a 10.7 Lion customac in 2011 and it's worked very well since then. Just took the plunge to finally update from 10.7 to El Capitan 10.11 and just wanted to post my build / results for anybody with a similar rig, cause I did get frustrated for a short while and this community is so...

Dear co-users with a hackingtosh, Got a problem. After upgrading from a fine working Yosemite system to the new el capitan OS I got stuck. After passing flawelessly through the setup I came into a horrible reboot loop. I have read a lot on the support forums... So far I have tried a lot of the...

Would appreciate some advise. Posted an earlier question to the forum regarding some oddities on my build. Pretty nice system. i7 4930k on a GA X79 UP4 board running 10.10.3. Had it running nicely (18K on the benchmark), fluid, everything functioned except audio which i THOUGHT caused the...

I followed the original guide by DavidHyde18 here and it works just great! HOWEVER! I have one remaining issue to resolve and its driving me insane. When CPUS=1 flag is entered (either in the Extra .plist or at boot), the sound to my FIREWIRE device works flawlessly, however, to utilise all the...

Hi, I have been following your tutorials and guides on installing Hackintosh on HP Probooks with configurations that are similar to my G6 Laptop. I downloaded the latest version of Yosemite and created a USB using UniBeast and MultiBeast. Specs: CPU: i3 3110 Chipset: HM76 Graphics: Intel HD...

I built a successful Hackintosh, so I thought, and then out of no where it crashes on me while I am using Pro Tools. The crash went like this: everything froze. I've been using Pro Tools along with some adobe programs this past month with zero issues. I have no idea what happened. The only way...