I've gotten High Sierra to boot on my new Desktop hackintosh, but I'm having issues with the graphics. With nv_disable=1, I see a lot of flickering and a very low frame rate. When I try to play an MP4 with VLC, I see black frames and white frames appear on the screen in quick succession. (I...
Had a clean install of Mojave which is working fine except for the graphics side. I'm using a Nvidia GTX 770 which should be supported via Lilu and Whatevergreen (they're installed in Clover), but I'm actually experiencing huge lags and flickering in the UI.
If no boot options and no...
Just booted into Sierra (10.12.6) on my new build. Went through MultiBeast and installed everything like normal. Used the new method of installing the NVIDIA Web Driver via Clover Configurator on my EFI recovery partition and was feeling pretty pleased with myself. Until I tried to restart to...
CORRECTION: CANNOT BOOT WITHOUT NVDA_DRV=1 OR NV_DISABLE=1
Hey all,
I recently just fresh installed El Capitan on my Hackintosh. I was able to go through all of my post-install with Multibeast 8.2.2; however, I cannot boot from clover without inputting either nv_disable=1 or nvda_drv=1. My...
First off, I have got everything to work including audio, keyboard, ethernet, expect the web drivers. Everything else works like a charm. I have a MSI GEFORCE® GTX 960 2GD5T OC as my graphics card. I have installed the latest web driver, version: 378.05.05.15f01 and the latest CUDA...
Hi,
So I've been searching for a fix for this the past 4 days.
Installing latest Nvidia drivers (f02) with latest Sierra (.4) results in boot halting at error "IOConsoleUsers gIOScreenLockState 3" using Asus Strix 980Ti.
I have 3 Asus Swift 27" monitors hooked up using display port.
You can see...
I have tried every possible boot flag there is without any luck. The computer will boot to the login page but freezes (the time does not change, nor do I see my mouse pointer). The computer does boot when i use the boot flag nv_disable=1, however, this disables my graphics card entirely. the...
Well, Booting without the boot flag cpus=1 will result in a stuck screen
-v: After:
it gets stuck (See photo).
Boot flags that I use: kernel-dev-mode=1 dart=0 nv_disable=1
I followed RehabMan's guide of Native power management for laptop's but I don't know how to verify success of this guide...
Well, that's the thing i can't boot successfully without the flag nv_disable=1
I already try nvda_drv=1 and the new NvidiaWeb Flag but no one can help, if use them get an apple screen stuck at half.
I know my GPU is a little old, but hope some support.
Please help
Hi guys,
the above system worked great with Yosemite and Clover with native OSX nvidia drivers and "InjectNvidia=1".
I now created a USB drive with Sierra and latest clover and the installation went fine except the GPU (had to use iMac10,1 instead of previous iMac8,1).
I can only get to the...
Hi All,
This is my first build and have had it successfully running El Cap d/b Win 10 for a week without much issue at all. I followed a guide to fix HDMI audio with SSDT-HDMI-NVIDIA-PEG0.ami file and the system would hang on reboot.
I tried a load of things to fix it but it looks like I have...
Hello friends, I managed to get my hackintosh work perfectly in dualboot, but I can not inciar the Mac partition, without having to use the flag "nv_disable = 1”, and many crashes occur because of the little graphics.
I've done installing Web Drivers in its latest version, as you can see in the...
Hi Everyone,
I just like to share my experience.
My Hardware:
Motherboard: GA-Z97M-DS3H
CPU: Intel 4690K
CPU Cooler: Corsair Hydro Series H75
RAM: Corsair Vengeance 16GB (2x8GB) DDR3 1600 MHz (PC3 12800)
Graphics: EVGA GeForce GTX 760 Super Clocked ACX 2GB
PSU: Corsair CX600
Case: Antec P50...
Hi,
I've upgraded my system with a SSD, so i had to Reinstall my perfectly working Hackintosh:banghead:. Now i had a Problem with my Nvidia GeForce GT 220. On my last Build i know i Installed the Web Driver an changed the Boot flag and everything works fine. Now after my reinstallation i had a...
Hello all,
I finally got my installation of El Capitan (10.11.2) working, using Clover to install and boot. The thing is, if I remove nv_disable=1 from the boot options I can't boot at all. Everything is updated and I have WebDriver 346.03.04 installed. nvda_drv=1 is also enabled in the boot...
Let me start by saying that I tried to fix this without starting a new thread, but I suck, so here is a new thread.
First off, I had a fully functional Hackintosh for the past 5 years. It was stable and I was running Mavericks. Then I decided to upgrade my graphics card to the Evga gtx 980 ti...
Beginner trying to get my feet wet. Thank you for the excellent guides and resources here. It's been an adventure-trying to get El Capitan on Dell XPS 8300 Core i7, 12 GB RAM, GeForce GTX560Ti (OEM)-trying first on external USB drive. Clover (first from here and then updated online on EFI...
Hey guys
Im using a gigabyte Geforce 9600 GT 512 MB i have successfully installed El Capitan using clover, the only problem is i cant boot properly i always have to use the nv_disable=1 bootflag, and when it does boot the graphics performance is very low and laggy.
when i install the nvidia...
OSX = El Capitan 10.11
Graphics = NVIDIA Geforce GTX 650
Memory = 3GB
CPU = Dual Core bla bla bla
Hi everybody! thank you all for the great community!
so, i never ask for help in the forum but i`m with a big problem. i just can`t boot my hackintosh without the flag ``nv_disable=1``, and as i...
Hey all,
I've got my build up and running for the most part. Everything is going well except that I can't get my GPU drivers installed, as Yosemite does not have support for the 980 built into the OS. When downloading from official Nvidia sites, the installer (such as "WebDriver-346.01.02f02")...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.