- Joined
- Oct 26, 2018
- Messages
- 6
- Motherboard
- Lenovo Yoga 730 15IKB
- CPU
- i5-8265U
- Graphics
- UHD 620 + GTX 1050 1920x1080
Hi,
i am a complete newbie and so far I was quite lucky.
I First tried Hackintosh on a 13" YOGA 730 and hit the jackpot by finding this thread and using the CLOVER from the Thread opener dragonflylee:
So the 13" model was working very good, even BT & Wifi after I swapped the Wifi card against that famous Dell DW1560 and added the needed files.
BUT I recently swapped the 13" model against the 15" model as I wanted the bigger screen and the GTX 1050.
Naive as I am I just used the CLOVER from my former 13" model.
Not surprisingly it causes trouble.
After reading up a bit I still feel lucky that it boots up to OSX at all but here are my griefs:
-It starts out booting quite fast but at 2/3 progress the screen blanks (at first I thought that's it).
If one is patient enough (I was by mistake as someone called) the login screen lights up, YEAH.
The blank screen phase takes between 1 to 100 seconds roughly.
Okay, NO PROBLEM, I could live with that (well, care for it later)
-The sound does not work
-Touchpad does not work
-Touchscreen does not work
-GTX 1050 not supported but I am aware no NVDIA drivers yet so I am fine with the Intel 620 working good...
I am aware by now that I was very lucky to get this far without much brain involved but for the life of me I cannot find a starting point.
As I am starting to grasp that the missing features must have something to do with SSDT / DSDT patching (hot or static) and that the existing patches in the CLOVER are valid for the 13" model but not for mine I saved the aml files with CLOVER-F4 method.
I also tried to decompile the files with some (only 3) errors.
I attached the *.aml & decompiled files and included a "decompileLog.txt" file that shows how I tried to decompile and with which result.
But I am completely lost now.
I have no idea wether it would be better to start at ZERO or wether to continue from this 13"-working configuration & kext modules.
And even if I would be able to decide on that I have no idea how to start.
Please help me getting a grip on this.
Thanks a lot !
Ender
i am a complete newbie and so far I was quite lucky.
I First tried Hackintosh on a 13" YOGA 730 and hit the jackpot by finding this thread and using the CLOVER from the Thread opener dragonflylee:
[solved] Lenovo Yoga 730-13IKB install High Sierra success
When i boot throw usb drive, After i boot the install macos high sierra 10.3.3 It asks Does printf work? Then it go blank screen with a white dote on the top left and freeze My laptop is Lenovo Yoga730 13inch with i5-8250U Chipset: Intel Sunrise Point-LP, Intel Kaby Lake-R Memery: 8007 MB...
www.tonymacx86.com
So the 13" model was working very good, even BT & Wifi after I swapped the Wifi card against that famous Dell DW1560 and added the needed files.
BUT I recently swapped the 13" model against the 15" model as I wanted the bigger screen and the GTX 1050.
Naive as I am I just used the CLOVER from my former 13" model.
Not surprisingly it causes trouble.
After reading up a bit I still feel lucky that it boots up to OSX at all but here are my griefs:
-It starts out booting quite fast but at 2/3 progress the screen blanks (at first I thought that's it).
If one is patient enough (I was by mistake as someone called) the login screen lights up, YEAH.
The blank screen phase takes between 1 to 100 seconds roughly.
Okay, NO PROBLEM, I could live with that (well, care for it later)
-The sound does not work
-Touchpad does not work
-Touchscreen does not work
-GTX 1050 not supported but I am aware no NVDIA drivers yet so I am fine with the Intel 620 working good...
I am aware by now that I was very lucky to get this far without much brain involved but for the life of me I cannot find a starting point.
As I am starting to grasp that the missing features must have something to do with SSDT / DSDT patching (hot or static) and that the existing patches in the CLOVER are valid for the 13" model but not for mine I saved the aml files with CLOVER-F4 method.
I also tried to decompile the files with some (only 3) errors.
I attached the *.aml & decompiled files and included a "decompileLog.txt" file that shows how I tried to decompile and with which result.
But I am completely lost now.
I have no idea wether it would be better to start at ZERO or wether to continue from this 13"-working configuration & kext modules.
And even if I would be able to decide on that I have no idea how to start.
Please help me getting a grip on this.
Thanks a lot !
Ender