[SUCCESS] Sierra 10.12 Clover | GA-Z68x-UD3H-B3 (v1.3) | 2500K | GTX 680

[bellhardtson]

Guys do you have any idea how to make the USB 3.0 ports working under Sierra?

LE: Nevermind, I figured that out by installing the GenericUSBXHCI.kext (Multibeast -> Drivers -> USB -> 3rd Party USB 3.0)

BTW: I installed the USB3-drivers, but I always had a system-crash, when running Chrome, and simultaneously plugged in a USB3-device. Strange thing, there has been the same problem with Mavericks.

Finally I bought this USB3-card by inateck. No problems since I don't use the board's USB3-ports anymore.

 

[johnmcdonnell]

USB 3.0 ports started working properly for me under Sierra 10.10.2 with UEFI BIOS U1n after removing GenericUSBXHCI.kext

This is discussed in more detail in the thread here

 

[nichoas]

Hey everyone. I followed this guide, but did not update to the UEFI. I did all the recommended mutibeast settings with the exception of legacy mode, and this is the error I receive after booting.

I was able to setup Sierra after initially installing, run multibeast, but now I cannot get past this screen. Any thoughts?

 

[konjow]

Can sameone tell me if Displayport works natively in GTX670/680 in Clover Sierra install?
Or is there easy fix?
Id like to know if this card will handle 4k through DP

 

[tomek123]

Thank you very much for sharing this tutorial! I have exactly the same mobo, but i7 2600k. It was very easy. Everything runs perfectly for now. My new-old r9 280x is running out of the box.

 

[tippmann32503]

Hey everyone,
I'm in the process of doing the same thing with the exact same motherboard. I updated my BIOS to U1N. For some reason when I was running unibeast the disk utility wouldn't recognize my new SSD (Samsung 850 EVO). I plugged into a different SATA port after unibeast was booting up it seemed to pick it up fine. However when I reset the machine after the install on the SSS to boot off off of the USB for multibeast, it wouldn't recognize the USB in the boot menu. When I unplug the SSD it boots up from unibeast no problem. Any ideas as to why? I'm thinking it's a BIOS setting.

 

[sgade]

Hi i Have a z68x-ud3h with 2500k on bios U1n
I have a 1tb SSD, that i want my system on.
I have no problem installing macOS Sierra - 10.12.3 - but when i run multibeast after reboot, to do the final setup. My hack won't boot.... it starts the boot but reboot automatically, half way through the boot
Please Help..........
(mind my spelling and hope it makes sense)

Update: When i boot for my USB stick and chose the SSD disk, i boots - no problem. What am i missing?

Update2: I cloned my working 10.12.3 with clonzilla to my SSD, and now it works, but clonzilla down sizes my HD. How can prevent that form happening? Can any one guide me, to settings i clonezilla? My working drive is 156GB and my SSD is 1,05TB....

Update3: I used Clonezilla and found out that it made the recovery partition 300BG..... I decided that i could do with out the recover partition (hence i have my usb...) - so using terminal i deletet the recovery partition and merged the 2 partitions. Now i have a fully working SSD 1TB large

 

[mjb152]

this works perfectly except for networking ! very weird. I have Yoesemite installed and that works well, did a clean install onto a new SSD and followed the guide, but I can;t get any of the 3 realtek options in Multibeast to work. I'm on a GA-Z68X-UD3H-B3 (rev. 1.0) , any ideas ?
No ethernet options show up in network preferences at all.

 

[Daylights]

this works perfectly except for networking ! very weird. I have Yoesemite installed and that works well, did a clean install onto a new SSD and followed the guide, but I can;t get any of the 3 realtek options in Multibeast to work. I'm on a GA-Z68X-UD3H-B3 (rev. 1.0) , any ideas ?
No ethernet options show up in network preferences at all.

What BIOS are you running?

 

[mjb152]

I'll check, but I just managed to resolve it. I have Yosemite and Sierra side by side, so I compared, and the realtek kext was installed in S/L/E but not working, no Ethernet card was detected. I copied it into the EFI, /CLOVER/ketxs/10.12 and it now works.
Not sure why MultiBeast didn't work for me, but at least it's fixed now