- Joined
- Jun 7, 2014
- Messages
- 7
- Motherboard
- Ivy Bridge (Medion Akoya E6232)
- CPU
- I3 3110M
- Graphics
- HD4000
- Mac
- Mobile Phone
Hi All,
So for a few days now i'm trying to setup an hackintosh on my Medion Akoya E6232, it's an Ivy Bridge HM76 Chipset, using the Intel I3 3110M 2.4 Ghz CPU/IGP HD4000, and 16GB ram, 120GB SSD Kingston, The Audio Codec is the ALC269VC (Dumped it in linux).
The screen is broken so i'm only able to use he HDMI port for now I don't know if this is causing the issue but I just wanted to include it here. Also i'm using dual boot mode when I select UEFI mode the HDMI port is not working until i get into OSX, also it enables the broken screen and stretches/clones it. (So i'm not able to see the post or entering the bios).
First I used an Sandy Bridge cpu on it (Core i7-2600K 4 Cores) however this baby is having an HD3000 IGP and somehow I read that they don't work that well in hackintosh. So i putted the I3 3110M back.
I installed my hackintosh (Sierra) with UniBeast, I download the config_HD4000_1366x768.plist renamed it to config.plist (Changed it to match my hardware)and changed the RtVariables, to make it boot with the newest clover. I was able to reach the installation without any problems.
So after installation I dumped my SSDT's and DSDT using clover (F4) method, that time I didn't had any DropOEM=True in my config.plis just to mention. I followed RehabMan dsdt/ssdt patching guide and injected them to clover (Also included in attachment). After reboot I had Full QE/CI. however without adjusting anything QE/CI stops working, and I discovered removing my SSDT's makes it to work again. Then I placed them back again, rebooted a few times and it was still working.
However this morning i booted it up and it didn't work anymore. I'm not sure what's going on here perhaps someone can assist me finding the cause?
I included a few files like the DSDT, SSDT, Config, and kext used, if you need anything else let me know!
Best Regards,
Toetje583
So for a few days now i'm trying to setup an hackintosh on my Medion Akoya E6232, it's an Ivy Bridge HM76 Chipset, using the Intel I3 3110M 2.4 Ghz CPU/IGP HD4000, and 16GB ram, 120GB SSD Kingston, The Audio Codec is the ALC269VC (Dumped it in linux).
The screen is broken so i'm only able to use he HDMI port for now I don't know if this is causing the issue but I just wanted to include it here. Also i'm using dual boot mode when I select UEFI mode the HDMI port is not working until i get into OSX, also it enables the broken screen and stretches/clones it. (So i'm not able to see the post or entering the bios).
First I used an Sandy Bridge cpu on it (Core i7-2600K 4 Cores) however this baby is having an HD3000 IGP and somehow I read that they don't work that well in hackintosh. So i putted the I3 3110M back.
I installed my hackintosh (Sierra) with UniBeast, I download the config_HD4000_1366x768.plist renamed it to config.plist (Changed it to match my hardware)and changed the RtVariables, to make it boot with the newest clover. I was able to reach the installation without any problems.
So after installation I dumped my SSDT's and DSDT using clover (F4) method, that time I didn't had any DropOEM=True in my config.plis just to mention. I followed RehabMan dsdt/ssdt patching guide and injected them to clover (Also included in attachment). After reboot I had Full QE/CI. however without adjusting anything QE/CI stops working, and I discovered removing my SSDT's makes it to work again. Then I placed them back again, rebooted a few times and it was still working.
However this morning i booted it up and it didn't work anymore. I'm not sure what's going on here perhaps someone can assist me finding the cause?
I included a few files like the DSDT, SSDT, Config, and kext used, if you need anything else let me know!
Best Regards,
Toetje583