F
FormerUser-594785
Guest
Not MacPro1,1 but iMacPro1,1.
Arghhhh..... Sorrrrrryyyyyyyy
Not MacPro1,1 but iMacPro1,1.
Please try the attached file -- rename it of course to config.plist. Comments:
Some BIOS settings to verify:
- Sets SMBIOS to Macmini8,1
- Puts iGPU into headless mode with platform ID 0x3E980003
- Your display monitor must be connected to your Vega GPU
- Enables "Trust" checkbox in SMBIOS
NOTE: If your system boots to a black screen (i.e. no output from Vega GPU) or your system simply does not boot, please let me know.
- BIOS --> IGFX --> Enabled
- BIOS --> Initial Display Output --> PCIe 1 Slot
The real iMac Pro uses Intel Xeon CPUs. These CPUs do not have integrated graphics (no iGPU). By using SMBIOS "iMacPro1,1" you are effectively disabling the iGPU. But this can lead to higher performance because macOS will use the AMD Vega for all GPU-related operations.Now it is working with SMBIOS of iMac Pro and enabled Intel Gpu ! What is the diffrence with the Mac mini, iMac and so on SMBIOS?
My last Hackintosh build was 7 years ago a lot learn again
Intel Gpu is enabled at Bios i was thinking this is importend for hardware encoding Adobe Premiere and others right?
Because you're using iMacPro1,1 please try this first:Thx for the detailed answer!
Now i'm stuck again at boot up i put my Wlan Bluetooth Card into the system and boot up hangs now.
It's a BCM94360CS2. Its connected on USB2.0 Header(F_USB2) on Mainboard at PCIEX1_2.
Normally i would say Pram reset will fix but i think not on Hackintosh .
Ah yeah you are right no igpu but you can use hw acceleration with the Intel Xeon when you encode H.264 on real imac pros on adobe premiere. i have to check it out if this is working with a hackintosh with 9900k.
Yes this is perfectly valid. There's a screenshot in Final Steps in Post-Installation that shows these USB port limit patches.
Do you plan to use an AMD RX 5xx or Vega 56/64 graphics card? Many professional applications make extensive use of compute units on GPUs so discrete GPUs are highly recommended. In this case I personally recommend:
Because the Fractal Design Define C TG has only 2 USB 3.0 ports on front panel and no USB Type C, it means we should remove SS01 from the Custom USB SSDT. This has been done in the attached file.
- SMBIOS = Macmini8,1 for now. But with 10.14.5 in the future, we will experiment with iMac19,1.
- Platform ID = 0x3E980003 (headless). You will have to connect display monitor to the AMD GPU.
- BIOS --> IGFX --> Enabled
- BIOS --> Initial Display Output --> PCIe 1 Slot
Because you're using iMacPro1,1 please try this first:
- BIOS --> IGFX --> Disabled
- Reboot -- does the system start?
Does it boot if you remove the WiFi card? If so, please try that, login to Mojave, Mount EFI partition, and compress/upload your Clover folder.No same like before.
It would be better to use WhateverGreen to configure the iGPU. If you provide your config.plist, I can make the changes. But you can also try the above procedure as you wrote it, but Inject Intel = checked on.Thanks a lot for Your help,
Yes, i have a Sapphire Radeon RX580 Pulse 8 GB.
If I understand correctly, should I set Clover Configurator like this for Macmini8,1 Sysdef?
Devices -> IntelGFX = 0x0
Graphics -> ig-platform-id = 0x3E980003
Graphics -> Inject Intel = uncheck
Does it boot if you remove the WiFi card? If so, please try that, login to Mojave, Mount EFI partition, and compress/upload your Clover folder.
Also grab a screenshot of the /Library/Extensions folder.