[SUCCESS] Gigabyte Designare Z390 (Thunderbolt 3) + i7-9700K + AMD RX 580

[MacArthur]

Hi ! I confirm that my Z490 with SMBIOS iMac 19.1 (iMac Retina 5K, 27-inch, 2019) on OpenCore 0.8.9 was successfully upgraded to macOS 13.3 (22E5219e) without any issues.

 

[CaseySJ]

Hi ! I confirm that my Z490 with SMBIOS iMac 19.1 (iMac Retina 5K, 27-inch, 2019) on OpenCore 0.8.9 was successfully upgraded to macOS 13.3 (22E5219e) without any issues.

Interesting...

Are you using these settings?

• SecureBootModel = Default (in Misc -> Security)
• csr-active-config = 00000000 (in NVRAM section)

 

[MacArthur]

1 . SecureBootModel: Disabled
2. csr-active-config: E7030000

 

[CaseySJ]

1 . SecureBootModel: Disabled
2. csr-active-config: E7030000

At long last, Monterey 12.6.4 incremental update got installed on the Z390 Designare.

• SecureBootModel = Default
• csr-active-config = 00000000
• OpenCore 0.8.9

Here's what I did, but I cannot be certain that this cleared up the problem:

• Logged out of Apple ID on all Hackintoshes
• Logged into iCloud.com with a browser and deleted all the Hackintoshes from my account
• Logged backed into the Hackintoshes one by one

 

[zgonda]

And if we tried with only : j160 (for example) in misc-->SecureBootModel instead of "default" without changing the smbios (19,1), what would happen ?

 

[CaseySJ]

And if we tried with only : j160 (for example) in misc-->SecureBootModel instead of "default" without changing the smbios (19,1), what would happen ?

Before signing out of Apple ID, I tried the Secure Boot Model for iMac20,2 but it didn’t work.

On the Z490 Vision D and Z390 Designare, Ventura 13.3 is still encountering a problem with installation (payload.014 mismatch).

So at this time only Monterey 12.6.4 has been successful.

 

[zgonda]

With my configuration (specified above) the update of Monterey in 12.6.4 was also carried out without problem (idem Ventura 13.3 beta) on the z390 designare...

 

[joostiphone]

Before signing out of Apple ID, I tried the Secure Boot Model for iMac20,2 but it didn’t work.

On the Z490 Vision D and Z390 Designare, Ventura 13.3 is still encountering a problem with installation (payload.014 mismatch).

So at this time only Monterey 12.6.4 has been successful.

I will keep track of your posts on the Ventura 13.3 matter, before upgrading. I don't want to ruin my perfectly working hackintosh

 

[phrfpeixoto]

@CaseySJ Could you please help with a Bootable Backup question?
I've followed the guide CCC Bootable Backup mini-guide, but in the end, my bootable APFS container only contains one volume. What did I do wrong?

Note: The only point where I deviated from the tutorial is the fact that I didn't use an EXTERNAL disk. I used an Internal one that used have Windows 10, but I did erase it as recommended in the tutorial.

 

[CaseySJ]

@CaseySJ Could you please help with a Bootable Backup question?
I've followed the guide CCC Bootable Backup mini-guide, but in the end, my bootable APFS container only contains one volume. What did I do wrong?

Note: The only point where I deviated from the tutorial is the fact that I didn't use an EXTERNAL disk. I used an Internal one that used have Windows 10, but I did erase it as recommended in the tutorial.

Alas, there's an updated procedure here:

Asus Z690 ProArt Creator WiFi (Thunderbolt 4) + i7-12700K + AMD RX 6800 XT

CaseySJ's Intel Alder Lake i7-12700K: Asus Z690 ProArt Creator WiFi + Intel i7-12700K + AMD RX 6800 XT Please do not quote this guide in its entirety. Post a link instead. This build guide applies to Asus Z790 ProArt Creator as well, but BIOS parameters may need to be adjusted All P-cores...

www.tonymacx86.com

The steps you may have omitted are these:

• Click the DESTINATION disk icon in the CCC main window
• The following will appear; select Legacy Bootable Copy Assistant... as shown
  
  
• Then the following will appear; select Allow CCC to erase '...'...
  
  
• Now when the cloning process begins it should use the APFS Replicator to clone both the system and data volumes