macOS 10.12.4 Update

[VioletDragon]

Yes I am, should I remove it? Also please note about my clover, Unibeast 7.1 does not work correctly, so i am using unibeast then Clover 4035 to reinstall EFI.

Why are you using MacBook1,1 SMBIOS on a Desktop? Needs to be iMac 14,2. The whole config is a mess. You have a lot of garbage in drivers64UEFI needs to be cleared up. AppleImageCodec-64.efi, AppleKeyAggregator-64.efi, AppleUITheme-64.efi, FirmwareVolume-64.efi, SMCHelper-64.efi need to be removed. Replace VBoxHfs-64.efi with HFSPlus.

 

[ccannon0]

Why are you using MacBook1,1 SMBIOS on a Desktop? Needs to be iMac 14,2. The whole config is a mess. You have a lot of garbage in drivers64UEFI needs to be cleared up. AppleImageCodec-64.efi, AppleKeyAggregator-64.efi, AppleUITheme-64.efi, FirmwareVolume-64.efi, SMCHelper-64.efi need to be removed. Replace VBoxHfs-64.efi with HFSPlus.

Again all that was installed by clover 4045. Following directions now.

 

[VioletDragon]

Again all that was installed by clover 4035. Following directions now.

Yes with drivers64UEFI. Not config the config has been edited incorrect.

 

[ccannon0]

Why are you using MacBook1,1 SMBIOS on a Desktop? Needs to be iMac 14,2. The whole config is a mess. You have a lot of garbage in drivers64UEFI needs to be cleared up. AppleImageCodec-64.efi, AppleKeyAggregator-64.efi, AppleUITheme-64.efi, FirmwareVolume-64.efi, SMCHelper-64.efi need to be removed. Replace VBoxHfs-64.efi with HFSPlus.

What should I do about OsxAptioFixDrv2?

 

[VioletDragon]

What should I do about OsxAptioFixDrv2?

Replace OsxAptioFixDrv2 with OsxAptioFixDrv. Config needs to be cleaned up better still create a new one.

 

[bumbuy]

You mean r4035?

No, its this Version: Clover_v2.4k_r4045-Legacy.pkg

 

[ccannon0]

No, its this Version: Clover_v2.4k_r4045-Legacy.pkg

Yes you are right. Thank you. Fixed in my post.

 

[ccannon0]

Replace OsxAptioFixDrv2 with OsxAptioFixDrv. Config needs to be cleaned up better still create a new one.

Ok I am recreating a new Unibeast USB. I want to find out the issue of why I can't boot from before. I have mounted the EFI before had to make sure Unibeast does not fail at mounting and install the bootloader.

 

[UtterDisbelief]

Ok I am recreating a new Unibeast USB. I want to find out the issue of why I can't boot from before. I have mounted the EFI before had to make sure Unibeast does not fail at mounting and install the bootloader.

Keep going!

As @violetdragon says, you probably need to start with a bare config.plist to get the system up and running. Don't worry about sound and USB 3.0, don't worry about serial numbers (you can always re-use your previous one etc)

If you have a UniBeast 7.0 stick, boot with it but don't choose the Sierra drive, instead boot to the UniBeast "External" volume. When the install screen comes up, don't go further, go to the Tools menu at the top and run Terminal. Then try copying the UniBeast config.plist over to your main Sierra drive using Terminal commands.

You will get there in the end

 

[AlphaFox]

If any one have a feed back about AmdRadeon9000controler and AmdX4000 kexts it will be helpfull for me

I can only assume you are working with an RX 470-480, if so:
https://www.tonymacx86.com/threads/enabling-amd-rx-4xx-cards-in-sierra.201364/