@kgp
Ive seen you have problems with AppleIntelInfo kext in pikers GitHub...
I have compiled one for you (Attached)
Steps (Just to be safe):
sudo chown -R root:wheel AppleIntelInfo.kext
sudo chmod -R 744 AppleIntelInfo.kext
sudo kextload AppleIntelInfo.kext
sudo cat /tmp/AppleIntelInfo.dat
sudo kextunload AppleIntelInfo.kext
Here is the Output from AppleIntelInfo on 7900x:
Code:
AppleIntelInfo.kext v2.9 Copyright © 2012-2017 Pike R. Alpha. All rights reserved.
Settings:
------------------------------------------
logMSRs..................................: 1
logIGPU..................................: 0
logCStates...............................: 1
logIPGStyle..............................: 1
InitialTSC...............................: 0xa16c44d882e (336 MHz)
MWAIT C-States...........................: 8224
Processor Brandstring....................: Intel(R) Core(TM) i9-7900X CPU @ 3.30GHz
Processor Signature..................... : 0x50654
------------------------------------------
- Family............................... : 6
- Stepping............................. : 4
- Model................................ : 0x55 (85)
Model Specific Registers (MSRs)
------------------------------------------
MSR_IA32_PLATFORM_ID.............(0x17) : 0x8000000000000
------------------------------------------
- Processor Flags...................... : 2
MSR_CORE_THREAD_COUNT............(0x35) : 0xA0014
------------------------------------------
- Core Count........................... : 10
- Thread Count......................... : 20
MSR_PLATFORM_INFO................(0xCE) : 0x70C2CF3012100
------------------------------------------
- Maximum Non-Turbo Ratio.............. : 0x21 (3300 MHz)
- Ratio Limit for Turbo Mode........... : 1 (programmable)
- TDP Limit for Turbo Mode............. : 1 (programmable)
- Low Power Mode Support............... : 0 (LMP not supported)
- Number of ConfigTDP Levels........... : 2 (additional TDP level(s) available)
- Maximum Efficiency Ratio............. : 12
- Minimum Operating Ratio.............. : 7
MSR_PMG_CST_CONFIG_CONTROL.......(0xE2) : 0x8402
------------------------------------------
- I/O MWAIT Redirection Enable......... : 1 (enabled, IO read of MSR(0xE4) mapped to MWAIT)
- CFG Lock............................. : 1 (MSR locked until next reset)
- C3 State Auto Demotion............... : 0 (disabled/unsupported)
- C1 State Auto Demotion............... : 0 (disabled/unsupported)
- C3 State Undemotion.................. : 0 (disabled/unsupported)
- C1 State Undemotion.................. : 0 (disabled/unsupported)
- Package C-State Auto Demotion........ : 0 (disabled/unsupported)
- Package C-State Undemotion........... : 0 (disabled/unsupported)
MSR_PMG_IO_CAPTURE_BASE..........(0xE4) : 0x11814
------------------------------------------
- LVL_2 Base Address................... : 0x1814
- C-state Range........................ : 1 (C6 is the max C-State to include)
IA32_MPERF.......................(0xE7) : 0x12C58577EEC
IA32_APERF.......................(0xE8) : 0x112BD97A0FC
MSR_FLEX_RATIO...................(0x194) : 0xE0000
------------------------------------------
MSR_IA32_PERF_STATUS.............(0x198) : 0x179B00000C00
------------------------------------------
- Current Performance State Value...... : 0xC00 (1200 MHz)
MSR_IA32_PERF_CONTROL............(0x199) : 0xC00
------------------------------------------
- Target performance State Value....... : 0xC00 (1200 MHz)
- Intel Dynamic Acceleration........... : 0 (IDA engaged)
IA32_CLOCK_MODULATION............(0x19A) : 0x0
IA32_THERM_INTERRUPT.............(0x19B) : 0x0
IA32_THERM_STATUS................(0x19C) : 0x884B0800
------------------------------------------
- Thermal Status....................... : 0
- Thermal Log.......................... : 0
- PROCHOT # or FORCEPR# event.......... : 0
- PROCHOT # or FORCEPR# log............ : 0
- Critical Temperature Status.......... : 0
- Critical Temperature log............. : 0
- Thermal Threshold #1 Status.......... : 0
- Thermal Threshold #1 log............. : 0
- Thermal Threshold #2 Status.......... : 0
- Thermal Threshold #2 log............. : 0
- Power Limitation Status.............. : 0
- Power Limitation log................. : 1
- Current Limit Status................. : 0
- Current Limit log.................... : 0
- Cross Domain Limit Status............ : 0
- Cross Domain Limit log............... : 0
- Digital Readout...................... : 75
- Resolution in Degrees Celsius........ : 1
- Reading Valid........................ : 1 (valid)
MSR_THERM2_CTL...................(0x19D) : 0x0
IA32_MISC_ENABLES................(0x1A0) : 0x850089
------------------------------------------
- Fast-Strings......................... : 1 (enabled)
- FOPCODE compatibility mode Enable.... : 0
- Automatic Thermal Control Circuit.... : 1 (enabled)
- Split-lock Disable................... : 0
- Performance Monitoring............... : 1 (available)
- Bus Lock On Cache Line Splits Disable : 0
- Hardware prefetch Disable............ : 0
- Processor Event Based Sampling....... : 0 (PEBS supported)
- GV1/2 legacy Enable.................. : 0
- Enhanced Intel SpeedStep Technology.. : 1 (enabled)
- MONITOR FSM.......................... : 1 (MONITOR/MWAIT supported)
- Adjacent sector prefetch Disable..... : 0
- CFG Lock............................. : 0 (MSR not locked)
- xTPR Message Disable................. : 1 (disabled)
MSR_TEMPERATURE_TARGET...........(0x1A2) : 0x690A00
------------------------------------------
- Turbo Attenuation Units.............. : 0
- Temperature Target................... : 105
- TCC Activation Offset................ : 0
MSR_MISC_PWR_MGMT................(0x1AA) : 0x402000
------------------------------------------
- EIST Hardware Coordination........... : 0 (hardware coordination enabled)
- Energy/Performance Bias support...... : 1
- Energy/Performance Bias.............. : 0 (disabled/MSR not visible to software)
- Thermal Interrupt Coordination Enable : 1 (thermal interrupt routed to all cores)
- SpeedShift Technology Enable......... : 0 (disabled)
- SpeedShift Interrupt Coordination.... : 0 (disabled)
- SpeedShift Energy Efficient Perf..... : 0 (disabled)
- SpeedShift Technology Setup for HWP.. : No (not setup for HWP)
MSR_TURBO_RATIO_LIMIT............(0x1AD) : 0x2D2D2D2D2D2D2D2D
------------------------------------------
- Maximum Ratio Limit for C01.......... : 2D (4500 MHz)
- Maximum Ratio Limit for C02.......... : 2D (4500 MHz)
- Maximum Ratio Limit for C03.......... : 2D (4500 MHz)
- Maximum Ratio Limit for C04.......... : 2D (4500 MHz)
- Maximum Ratio Limit for C05.......... : 2D (4500 MHz)
- Maximum Ratio Limit for C06.......... : 2D (4500 MHz)
- Maximum Ratio Limit for C07.......... : 2D (4500 MHz)
- Maximum Ratio Limit for C08.......... : 2D (4500 MHz)
MSR_TURBO_RATIO_LIMIT1...........(0x1AE) : 0x1C1814100A080402
------------------------------------------
- Maximum Ratio Limit for C09.......... : 2 (200 MHz)
- Maximum Ratio Limit for C10.......... : 4 (400 MHz)
IA32_ENERGY_PERF_BIAS............(0x1B0) : 0x1
------------------------------------------
- Power Policy Preference...............: 1 (highest performance)
MSR_POWER_CTL....................(0x1FC) : 0x2924005B
------------------------------------------
- Bi-Directional Processor Hot..........: 1 (enabled)
- C1E Enable............................: 1 (enabled)
MSR_RAPL_POWER_UNIT..............(0x606) : 0xA0E03
------------------------------------------
- Power Units.......................... : 3 (1/8 Watt)
- Energy Status Units.................. : 14 (61 micro-Joules)
- Time Units .......................... : 10 (976.6 micro-Seconds)
MSR_PKG_POWER_LIMIT..............(0x610) : 0x3FFF80014FFF8
------------------------------------------
- Package Power Limit #1............... : 4095 Watt
- Enable Power Limit #1................ : 1 (enabled)
- Package Clamping Limitation #1....... : 0 (disabled)
- Time Window for Power Limit #1....... : 10 (2560 milli-Seconds)
- Package Power Limit #2............... : 4095 Watt
- Enable Power Limit #2................ : 1 (enabled)
- Package Clamping Limitation #2....... : 1 (allow going below OS-requested P/T state setting Time Window for Power Limit #2)
- Time Window for Power Limit #2....... : 1 (5 milli-Seconds)
- Lock................................. : 0 (MSR not locked)
MSR_PKG_ENERGY_STATUS............(0x611) : 0x3D88B8F
------------------------------------------
- Total Energy Consumed................ : 3938 Joules (Watt = Joules / seconds)
MSR_CONFIG_TDP_NOMINAL...........(0x648) : 0x21
MSR_CONFIG_TDP_LEVEL1............(0x649) : 0xE4000000190460
MSR_CONFIG_TDP_LEVEL2............(0x64a) : 0xE4000000190460
MSR_CONFIG_TDP_CONTROL...........(0x64b) : 0x80000000
MSR_TURBO_ACTIVATION_RATIO.......(0x64c) : 0x0
MSR_PKGC3_IRTL...................(0x60a) : 0x0
MSR_PKGC6_IRTL...................(0x60b) : 0x0
MSR_PKG_C2_RESIDENCY.............(0x60d) : 0xDCD73819D8
MSR_PKG_C3_RESIDENCY.............(0x3f8) : 0x0
MSR_PKG_C2_RESIDENCY.............(0x60d) : 0xDCD73819D8
MSR_PKG_C6_RESIDENCY.............(0x3f9) : 0x22DFB4E3845
IA32_TSC_DEADLINE................(0x6E0) : 0xA16C8539F3B
CPU Ratio Info:
------------------------------------------
Base Clock Frequency (BLCK)............. : 100 MHz
Maximum Efficiency Ratio/Frequency.......: 12 (1200 MHz)
Maximum non-Turbo Ratio/Frequency........: 33 (3300 MHz)
Maximum Turbo Ratio/Frequency............: 45 (4500 MHz)
P-State ratio * 100 = Frequency in MHz
------------------------------------------
CPU P-States [ (12) 29 ]
CPU C6-Cores [ 0 2 4 6 8 9 12 15 16 18 ]
CPU P-States [ (12) 18 29 ]
CPU C6-Cores [ 0 2 4 6 8 9 10 12 14 15 16 18 19 ]
CPU P-States [ (12) 18 22 29 ]
CPU C6-Cores [ 0 2 4 6 7 8 9 10 12 14 15 16 18 19 ]
CPU P-States [ (12) 18 21 22 29 ]
CPU C6-Cores [ 0 2 4 5 6 7 8 9 10 12 14 15 16 18 19 ]
CPU P-States [ (12) 18 21 22 28 29 ]
CPU C6-Cores [ 0 2 3 4 5 6 7 8 9 10 11 12 14 15 16 18 19 ]
CPU P-States [ (12) 18 21 22 28 29 31 ]
CPU C6-Cores [ 0 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 ]
CPU P-States [ (12) 17 18 21 22 28 29 31 ]
CPU P-States [ (12) 16 17 18 21 22 28 29 31 ]
CPU P-States [ (12) 16 17 18 19 21 22 28 29 31 ]
CPU P-States [ (12) 16 17 18 19 21 22 26 28 29 31 ]
CPU P-States [ (12) 13 16 17 18 19 21 22 26 28 29 31 ]
CPU P-States [ 12 13 16 17 18 19 21 22 23 26 28 29 31 (45) ]
CPU C6-Cores [ 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 ]
CPU P-States [ (12) 13 16 17 18 19 20 21 22 23 26 28 29 31 45 ]
CPU P-States [ (12) 13 16 17 18 19 20 21 22 23 26 28 29 31 32 45 ]
CPU P-States [ (12) 13 16 17 18 19 20 21 22 23 25 26 28 29 31 32 45 ]
CPU P-States [ 12 13 16 17 18 19 20 21 22 23 25 26 28 29 31 32 (33) 45 ]
CPU P-States [ (12) 13 16 17 18 19 20 21 22 23 24 25 26 28 29 31 32 33 45 ]
CPU P-States [ 12 13 16 17 18 19 20 21 22 23 24 25 26 28 29 30 31 32 33 (45) ]
CPU P-States [ 12 13 16 17 18 19 20 21 22 23 24 25 26 28 29 30 31 32 33 45 ]
CPU P-States [ (12) 13 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 45 ]
CPU P-States [ (12) 13 14 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 45 ]
CPU P-States [ (12) 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 45 ]
CPU P-States [ 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 (43) 45 ]
CPU P-States [ (12) 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 43 45 ]
CPU P-States [ 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 (33) 34 35 36 43 45 ]
CPU P-States [ 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 43 (45) ]
CPU P-States [ 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 (33) 34 35 36 37 38 43 45 ]
CPU P-States [ 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 43 45 ]
@Menno87
I don't have this option in my Bios... (Bios is 802)
You have an Rampage 6 Extreme with a i9-7900x ???
Thats reaaaaalllyyyy strange...
I will make a picture in a second...
About the Thunderbolt Card...
I think the card doesn't combine two DP to one Type-c
im not sure, but I seems like the card do 1DP to 1Type-C and the other DP to the second Type-C...
As far I know, the 5k displays need 2x DP, instead of one... Because the Manufacturers still use DP 1.2 instead of 1.4...
And that 2xDP to one Type-C is sth Apple Proprietary... (but I can be wrong)
The other thing is, are you sure, that your Gigabyte TB3 cards work as TB3 with Mac?
Because as far I know, every TB3 card runs in TB2 mode on Mac...
But I can be wrong here too... Thats what ive read in the forums (don't ask me where exactly)
Picture is Comming, Cheers
EDIT:
LOLOLOL, I can swear that I didn't had that option before....
After you posted your picture, I have the option too
LOL
Cheers