Compatability with 10th Gen Intel

[r0ger]

No, its not working, Along with sound and trackpad,

Updated to 10.15.5

View attachment 477164

Hi I see on the screenshot your battery percentage is working, how do you do it?

 

[Killuminati91]

Hi I see on the screenshot your battery percentage is working, how do you do it?

SmcBattery and the proper acpi patches (Depending on your specific laptop) worked for me.

 

[nafjang]

Here you go, based on muhydeen's and TUNIN96's work. Probably need to remove the ACPI files on different machines.
While we wait for proper acceleration we should figure out the trackpads and audio.

For you guys who got the installer to run: Did you also face the error messages? If so, how did you get rid of them?
I tried "date" in terminal, which freed me from the first "Can not installed on this machine" error, but I cant get rid of the other two (which dont seem to be critical).

HP 14s dq1028tu
i5 1035g1
DDR 4 8 GB 2666
M.2 256GB+Optane 16GB
Use EFI error
Help

 

[Killuminati91]

Try to get a screenshot of the exact kernel panic moment, this info is of no use. Try to remove all patches under acpi/patched. If that doesn’t work it’s probably your SSD (optane) remove it and try to run the setup again.

 

[chekerlamer]

HP 14s dq1028tu
i5 1035g1
DDR 4 8 GB 2666
M.2 256GB+Optane 16GB
Use EFI error
Help View attachment 477192

Seems like your laptop just like me but you are with the i5 version. Go check my repository. I've been disable intel optane but you may need to do some adjustments for your laptop.

ferdy42id/hackintosh-14s-dq1013tu

This is my laptop's backup of CLOVER EFI bootloader. - ferdy42id/hackintosh-14s-dq1013tu

github.com

 

[nafjang]

Try to get a screenshot of the exact kernel panic moment, this info is of no use. Try to remove all patches under acpi/patched. If that doesn’t work it’s probably your SSD (optane) remove it and try to run the setup again.

I forgot to install the kext nvme

 

[nafjang]

Seems like your laptop just like me but you are with the i5 version. Go check my repository. I've been disable intel optane but you may need to do some adjustments for your laptop.

ferdy42id/hackintosh-14s-dq1013tu

This is my laptop's backup of CLOVER EFI bootloader. - ferdy42id/hackintosh-14s-dq1013tu

github.com

I forgot to install the kext nvme

 

[nafjang]

install complete vga show 7mb

 

[Sparkesj2]

Afternoon all. I was just wondering if anyone could shine some light on a problem I’ve been having installing Catalina 10.15.3,4,5 on my 10th gen Intel i5 laptop. I’ve been struggling with it for a while but was able to get to the installer after a bit of fumbling about. Only issue is it will work for so long until I come to either format the drive where it sometimes freezes half way through where I then have to force shut down. Then, if I come to install macOS, it will sometimes go through the installer before getting an error at the two minutes left mark or it will freeze normally about 12 minutes left. After I get the two minutes left error and reboot, I can then boot the installer from the internal drive where it again starts off OK but freezes at 13 or 12 minutes left. However, sometimes it will go on till around 9 minutes left before freezing. When I try it via the recovery partition as I have Internet via an Apple USB Ethernet dongle, it will go on for about an hour and get a message saying it can’t install.

Any help would be much appreciated as I have tried everything I possibly could and have researched for hours to no avail. Please note I have tried 10.15.3 4 and 5 just to make sure that’s not the issue. I seem to have more luck with 10.15.5 which I obtained from the App Store whereas the other two came from gibmacos.

 

[Killuminati91]

That seems to be related to Clover. Someone on another forum had a working OpenCore config and could get through the installer without errors. Everyone doing it through Clover is running into the same errors.