Contribute
Register

Guide To Install Yosemite on HP Laptops with Clover UEFI

Hi guys, I've tried both installations and whenever I do an install I only see my usb stick and not one of my HD or SSD, what I'm doing wrong. my laptop is an HP Envy t15 j051nr. Thanks in advance.
 
installed ar5b195 card, everything works great just led was worked for few seconds then it gone back to orange ? i've repatched dsdt still it's not showing correct LED but over all wifi working great, just worried about LED could lead to some other problems.
Thanks for support and guide.
 
Hi guys, I've tried both installations and whenever I do an install I only see my usb stick and not one of my HD or SSD, what I'm doing wrong. my laptop is an HP Envy t15 j051nr. Thanks in advance.

This guide is only for ProBook/EliteBook. Post a separate thread in the Yosemite Laptop Support forum.
 
installed ar5b195 card, everything works great just led was worked for few seconds then it gone back to orange ? i've repatched dsdt still it's not showing correct LED but over all wifi working great, just worried about LED could lead to some other problems.
Thanks for support and guide.

The LED does not represent the state of the device. Ignore it.
 
My yosemite hot mavericks on 5-10 degrees C. all as?
 
Clearly it is not showing your USB. You must have created your USB incorrectly...

Success!
The problem was in my old USB stick.. Suddenly it has worked.

Thanks very muck for the guide and help! :thumbup:

The fan is spinning very fast and loud. In the guide it's said - Fan behavior: Readings only, but can I use different options?
 
Help please, I cannot boot Yosemite from hard drive
I went through the clean installation guide without any problems using the 2a Method, but after I ran clover and restarted I got the boot options(OSX Yosemite and HD Recovery) and when I chose my Yosemite Hard drive installation, it shows a black screen with the white apple logo for a couple of seconds and then my system reboots by itself (after the restart, the system shows the boot options again and if I choose Yosemite hard drive installation or HD Recovery, the same issue happens)

Note: if I use clover USB I can boot to hard drive where yosemite is installed. (I have tried clean installs 3 times)

My system:
HP Elitebook 820 G1
CPU: Intel i5-4200u
Graphics: HD 4400
Ram: 12GB
SSD: 120GB Intel ssd 530series


2a. (Easy guide, but may stuck in blank screen)
- Download Yosemite Install app from AppStore.
- Launch terminal and run the following script:
Code:
sudo /Applications/Install\ OS\ X\ Yosemite.app/Contents/Resources/createinstallmedia --volume  /Volumes/MacUSB --applicationpath /Applications/Install\ OS\ X\ Yosemite.app --nointeraction
- Your Yosemite Installer partition will be renamed "Install OS X Yosemite"
View attachment troubleshooting-files.zip

************************F I X E D********************************************
Just needed to use down arrow key to show all DSDT Options in Clover installer(I didn't choose my model DSDT because I could not see it.)

Now I'm up and running
 
Last edited:
Help please, I cannot boot Yosemite from hard drive
I went through the clean installation guide without any problems using the 2a Method, but after I ran clover and restarted I got the boot options(OSX Yosemite and HD Recovery) and when I chose my Yosemite Hard drive installation, it shows a black screen with the white apple logo for a couple of seconds and then my system reboots by itself (after the restart, the system shows the boot options again and if I choose Yosemite hard drive installation or HD Recovery, the same issue happens)

Note: if I use clover USB I can boot to hard drive where yosemite is installed. (I have tried clean installs 3 times)

My system:
HP Elitebook 820 G1
CPU: Intel i5-4200u
Graphics: HD 4400
Ram: 12GB
SSD: 120GB Intel ssd 530series

Post troubleshooting files. See post #1.
 
Back
Top