Contribute
Register

[ISSUE] MISSING Bluetooth Controller Transport

Status
Not open for further replies.
Again, please put your specific motherboard model, CPU model, and GPU model in the system information on the left and/or in your signature. It's much easier to provide reasonable advice without searching the thread for that information.
 
Jeepers
GA-H87N-WIFI |  i7 4790S |  GeForce GT 740
ammulder said:
Again, please put your specific motherboard model, CPU model, and GPU model in the system information on the left and/or in your signature. It's much easier to provide reasonable advice without searching the thread for that information.
Click to expand...
Done!
 
[SUB]I had the same problem. I was using the integrated graphic instead of my nvidia gt730 I tried removing all kext folders I tried using another usb port but no success, finally I put back my nvidia graphic and it worked[/SUB]
 
I am getting stuck on the same Bluetooth missing error.
My system specs:
msi H97M-G43
i5-4460 (using intergrated HD4600 graphics)
8gb 1600mhz ddr3 memory

I have tried most of the boot flags that are suggested here but none are working as i still get the same error. any help would be greatly appreciated as although i have been looking at making a hackintosh for quite some time now, it is my first one.

Thanks,
Bay101 :D
 
bay101 said:
I am getting stuck on the same Bluetooth missing error.
My system specs:
msi H97M-G43
i5-4460 (using intergrated HD4600 graphics)
8gb 1600mhz ddr3 memory

I have tried most of the boot flags that are suggested here but none are working as i still get the same error. any help would be greatly appreciated as although i have been looking at making a hackintosh for quite some time now, it is my first one.

Thanks,
Bay101 :D
Click to expand...

If you already have El Cap installed try this:
In the Clover config.plist try setting Graphics / Inject / Intel to <true/>
If you haven't reached the installer yet, make sure you've got your BIOS set up to
use integrated graphics first. It's usually called "init display first" Also make sure
to place the installer, UniBeast USB drive, into a rear usb 2.0 port.
 
trs96 said:

If you already have El Cap installed try this:
In the Clover config.plist try setting Graphics / Inject / Intel to <true/>
If you haven't reached the installer yet, make sure you've got your BIOS set up to
use integrated graphics first. It's usually called "init display first" Also make sure
to place the installer, UniBeast USB drive, into a rear usb 2.0 port.
Click to expand...


I dont have el capitan installed currently and have done what you suggested with no luck, the same problem still exists. Is there anything else i should try?
 
Hello,

I have about the same problem..
My specs are
Mobo:Asus Maximus Viii Hero
cpu: i5 6600k
gpu:Gigabyte gtx 970 G1 Gaming
Ram:2x8gb(3000Mhtz,Ripjaws 4)
ssd:samsung evo 500gb
coolermaster storm trooper
coolermaster neptune 240m

I successful make my Usb with unibeast 6.1.1 with El capitan 10.11.03 and i get to clover but i cant get to installation i finally get black screen with a white circle and a line accross!
By reading the skylake starter guide I copied the cofig plist from starter guide my efi partition of usb on kexts folder other ,10.11 and 10.10 the following

 
up
 
Fixed it, after hours of searching and trying different boot flags, re making the usb and etc. It turns out that mac does not in fact like vga and will not boot on a vga display to the set-up. Changed it to another monitor that supports HDMI, and BAM! worked instantly with no bootflags. Just thought I would put my findings here for anyone else that has this issue to try! :headbang:
 
Status
Not open for further replies.
Copyright © 2010 - 2024 tonymacx86 LLC
Back
Top