No Sound - Realtek ALC AppleHDA [Guide]

[toleda]

I've attached the (I believe) necessary files

Incorrect conclusion.
Wrong EFI partition mounted, no MultiBeast/audio edits present in files attached.
Verify BIOS/Peripherals/HD Audio/Enabled
Try again.
Attach all requested new files.

 

[RedBedford]

Incorrect conclusion.
Wrong EFI partition mounted, no MultiBeast/audio edits present in files attached.
Verify BIOS/Peripherals/HD Audio/Enabled
Try again.
Attach all requested new files.

I've mounted EFI partition from Yosemite, which is my SSD. The only other two options are my slave (storage) drive and my backup drive. Where I'm probably getting confused (see clover-configs below) is there are a TON of different files. I've attached the EFI folder where the config is found in /EFI/EFI/CLOVER/config.plist EFI.zip) as well as the one found in /Yosemite/EFI/CLOVER/config.plist. I have no idea why there are so many of these things and I'm probably getting confused because of it.

Also, I'm not sure where to verify the HD Audio Enabled thing. I couldn't find that in multibeast or clover or either config.plist (opened in xcode)

 

[toleda]

not sure where to verify the HD Audio Enabled thing

BIOS settings, see motherboard manual.
Attach Terminal: diskutil list

 

[RedBedford]

BIOS settings, see motherboard manual.
Attach Terminal: diskutil list

attached

 

[toleda]

attached

Install Community Software/EFI Mounter v3
Select disk0 (assuming Sierra is the Yosemite partition)

 

[RedBedford]

Install Community Software/EFI Mounter v3
Select disk0 (assuming Sierra is the Yosemite partition)

Downloaded and mounted.

 

[toleda]

Downloaded and mounted.

Double click cloverALC ...

 

[RedBedford]

Double click cloverALC ...

Did it

 

[toleda]

Did it

Should be obvious by now:
Restart. See Problem Reporting, Post #1; attach all requested files

 

[RedBedford]

1. No audio devices. Ran CloverALC.
2. My build is Yosemite 10.10.5 on a computer held in a Corsair 500R that is running on an Intel i7 4790k with 16GB of Crucial Ballistix Tactical RAM on a Gigabyte GA-Z97X-UD5H-BK motherboard and all graphics are handled by my Gigabyte GTX 960 Windforce 2GB.
   1. MOTHERBOARD: Gigabyte GA-Z97X-UD5H-BK
   2. RAM: Crucial Ballistix Tactical 16GB
   3. PROCESSOR: Intel core i7 4790k
   4. GRAPHICS: Gigabyte GTX 960 Windforce 2GB
   5. CASE: Corsair 500R
   6. OSX VERSION: Yosemite 10.10.5
3. Followed your instructions to this point
4. Attached IOReg (joshuabedford.ioreg)
5. Not found
6. Not found
7. I went to Console/All Messages. Searched for 'kernel sound' nothing came up. I Probably misunderstood.
8. audio.jpg attached
9. possibly irrelevent but It WAS installed just (i think) not in use anymore
10. Attached /EFI/CLOVER/config.plist & Not sure what DPCIManager/misc/BootLog is
11. Headphones
    1. AKG K240 Mk ii headphones
       
    2. Front case port
    3. No Output devices

When running the script (your script: audio_cloverALC-120_v1.0d.command) right after I enter my password the terminal window disappears. There is no confirmation or the other steps listed.