- Joined
- Apr 18, 2019
- Messages
- 16
- Motherboard
- Gigabyte Z390 UD
- CPU
- i3-8100
- Graphics
- RX 580
- Mac
Hello,
I’m having the same problem as in this thread, but switching to APFS only changed the installation screen to say 13 mins vice 15. I can’t get past the installation to setup or desktop.
At the clover menu I select “Boot macOS Install from Install macOS Mojave.” At disk utility I erase my internal SSD, rename to Mojave, selecting GUID Partition Map and APFS (I’d like to do APFS encrypted but I’m omitting that at the moment to reduce variables).
I proceed with the installation which leads to a reboot and takes me to the clover menu with options: External, APFS Preboot, and APFS “Boot macOS Install from Mojave”. Selecting the last option leads me through two apple loading screens, then to a screen that says “Installing on “Mojave” about 13 minutes remaining.” After about 10 seconds my screen goes black, and then the system reboots and I’m back to clover again. The behavior is the same each time I select the APFS Mojave option.
*build details (also in account details)*
*all selected from recommended list*
Motherboard: Gigabyte Z390 UD
CPU: Intel Core i3-8100
Graphics: Sapphire Radeon Nitro+ RX 580 8GB
RAM: Corsair Vengeance LPX 16GB (2x8GB) DDR4 DRAM 2400MHz C16
SSD: Samsung Evo 1TB
Network card: TP-Link Archer T9E
USB drive (unibeast): Samsung MUF-32AB/AM FIT Plus 32GB - 200MB/s USB 3.1 Flash Drive
Note: neither my mobo nor my case have any USB 2 ports
*bios settings*
Unibeast 9.2 installed on USB using guide. Yes, I installed on the parent drive name after “view all devices” in Disk Utility.
Multibeast 11.2 copied to Install Mojave USB
I included a few pictures of my screen from verbose output. Is there a log file I can access to copy the full output?
I reposted this.
I’m having the same problem as in this thread, but switching to APFS only changed the installation screen to say 13 mins vice 15. I can’t get past the installation to setup or desktop.
At the clover menu I select “Boot macOS Install from Install macOS Mojave.” At disk utility I erase my internal SSD, rename to Mojave, selecting GUID Partition Map and APFS (I’d like to do APFS encrypted but I’m omitting that at the moment to reduce variables).
I proceed with the installation which leads to a reboot and takes me to the clover menu with options: External, APFS Preboot, and APFS “Boot macOS Install from Mojave”. Selecting the last option leads me through two apple loading screens, then to a screen that says “Installing on “Mojave” about 13 minutes remaining.” After about 10 seconds my screen goes black, and then the system reboots and I’m back to clover again. The behavior is the same each time I select the APFS Mojave option.
*build details (also in account details)*
*all selected from recommended list*
Motherboard: Gigabyte Z390 UD
CPU: Intel Core i3-8100
Graphics: Sapphire Radeon Nitro+ RX 580 8GB
RAM: Corsair Vengeance LPX 16GB (2x8GB) DDR4 DRAM 2400MHz C16
SSD: Samsung Evo 1TB
Network card: TP-Link Archer T9E
USB drive (unibeast): Samsung MUF-32AB/AM FIT Plus 32GB - 200MB/s USB 3.1 Flash Drive
Note: neither my mobo nor my case have any USB 2 ports
*bios settings*
- Load Optimized Defaults
- If your CPU supports VT-d, disable it
- (Skipped - could not find) If your system has CFG-Lock, disable it
- (Skipped - hidden unless you disable CSM Support. Doing this step doesn’t fix the problem.) If your system has Secure Boot Mode, disable it
- Set OS Type to Other OS
- If your system has IO Serial Port, disable it
- Set XHCI Handoff to Enabled
- (Skipped) If you have a 6 series or x58 system with AWARD BIOS, disable USB 3.0
Unibeast 9.2 installed on USB using guide. Yes, I installed on the parent drive name after “view all devices” in Disk Utility.
Multibeast 11.2 copied to Install Mojave USB
I included a few pictures of my screen from verbose output. Is there a log file I can access to copy the full output?
I reposted this.