Intel NUC 10 Frost Canyon

[Leesureone]

I see the usual items and above them the install disk. I would say it's the same as any update/upgrade of macOS. The install disk is selected on the first reboot, but then it silently fails and come back to the menu where no item is selected. If I try again to select the install disk the same scenario repeats. If I choose my usual boot drive the NUC properly starts.

Okay, I understand what you are saying now, not sure why that would happen unless there is something wrong on Apple's end with the file

 

[epal]

On your NUC which EFI are you using?

maybe I can compare it with mine so I can see the differences too

the new OC 0.7 EFI, Error when booting, it appears in split second.

 

[Leesureone]

the new OC 0.7 EFI, Error when booting, it appears in split second.

Hi, there are two errors in the config.plist to fix using a plist editor.
1. Change the entry under PlatformInfo/Generic from AdviseWindows to AdviseFeatures
2. Change the entry under UEFI/Audio to match the screen shot below or at least that has been reported to correct that error message

 

[Jeffray]

Hey Amigos, i have an Intel nuck 10th gen with an i7 cpu.

i installed macos big sur 11.4 , also could manage to get wifi and bluetooth to work.

Following Trouble still occure:
1.My integrated SD-card reader seems not to work
2. After doin a Geekbenchmark (single score:1148 Multicore:4861) i realised that my Cpu is only working with the Base frequency of 1,6GHZ, is there any posibility to let the cpu drive always with 4,0 GHZ?
the range of this Cpu is going from 1,1GHZ - 4,7 GHZ

THanks for your help bros =)

 

[Leesureone]

Hey Amigos, i have an Intel nuck 10th gen with an i7 cpu.

i installed macos big sur 11.4 , also could manage to get wifi and bluetooth to work.

Following Trouble still occure:
1.My integrated SD-card reader seems not to work
2. After doin a Geekbenchmark (single score:1148 Multicore:4861) i realised that my Cpu is only working with the Base frequency of 1,6GHZ, is there any posibility to let the cpu drive always with 4,0 GHZ?
the range of this Cpu is going from 1,1GHZ - 4,7 GHZ

THanks for your help bros =)

There are kexts that may or may not enable the SD-Card reader, I've attached an example. Users that have tried report odd behaviour, cannot boot with a card installed.
Meanwhile your geekbench scores are consistent with this device, you can go back several posts and see. Because CPU Emulation is needed to allow the device to boot it can't function natively and is likely the reason. This is also mentioned here several times. #743

 

[Jeffray]

There are kexts that may or may not enable the SD-Card reader, I've attached an example. Users that have tried report odd behaviour, cannot boot with a card installed.
Meanwhile your geekbench scores are consistent with this device, you can go back several posts and see. Because CPU Emulation is needed to allow the device to boot it can't function natively and is likely the reason. This is also mentioned here several times. #743

Thank you bro
i tried to read /search about the cpu behaviour, but 73 pages is a lot and i didn't had so much time, sorry for that.

Would you say that that the score is okay? It seems slightly better than the minimac 2018, but i wanted to get closer to the new m1 :/

Wish ya a good day

 

[Jeffray]

I've

Now, i've update my EFI, that work super stabile.
TB work fine in HOTPLUG, and eGPU now is support.
iGPU is fixed, and now the audio are support for all port HDMI/TB/DP.

Let me know for any problems.

Could you share the updated files?

 

[Leesureone]

Thank you bro
i tried to read /search about the cpu behaviour, but 73 pages is a lot and i didn't had so much time, sorry for that.

Would you say that that the score is okay? It seems slightly better than the minimac 2018, but i wanted to get closer to the new m1 :/

Wish ya a good day

It’s comparable, did you see the link I posted that shows a benchmark comparison between the NUC8 and the NUC10? The CPU emulation requirement has a negative impact on the NUC10, no where near an M1 chip performance for sure.

The updated files you are looking for are on his GitHub page he has linked in back pages. Just follow his posts and you will get there.
He has almost the same scores as you

 

[Jeffray]

It’s comparable, did you see the link I posted that shows a benchmark comparison between the NUC8 and the NUC10? The CPU emulation requirement has a negative impact on the NUC10, no where near an M1 chip performance for sure.

The updated files you are looking for are on his GitHub page he has linked in back pages. Just follow his posts and you will get there.
He has almost the same scores as you

Thanks a lot,
yeh i saw the post but thaught it wouldnt be up 2 date
Hmm i ordered a barebonepc with an i5 10500 just for testing reasons and i will decide after which setup will fit my needs

 

[hkfriends]

Hi there
I am new to this forum, I have my new NUC10 i7 version from China.
It was modded with BMC943602CS WiFi and BT card.

May I know how I can start with install macOS ? Which version is working great on my hardware? Thanks a lot