[Guide] HP ProBook/EliteBook/Zbook using Clover UEFI hotpatch (10.11)

[uggitt]

Sounds like a hardware/installation problem.
Perhaps you didn't connect the antennas correctly.
Test in Windows to verify your hardware.

Also, your ioreg shows Android File Transfer. Read related topic in FAQ.
https://www.tonymacx86.com/threads/faq-read-first-laptop-frequent-questions.164990/

Hi, I only have one wifi antenna in my 450 G2 and after swapping the connection to the other connector on my wlan card I now have bluetooth but I am unable to connect to any device, be it an apple device or android device. It will connect briefly then disconnect. When I try and connect again i get a message 'Network is Unavailable, Make sure network access is enabled'.

I have removed Android Transfer.

If you need the reporting files again please let me know.

Thanks in advance.

 

[DoHaiSon]

dear sir
i have problem with usb port and something when complete install
1. USB port: usb 3.0 port worked but problem is sometime (50%) 1 connect new device or reconnect them (like a mouse), my hackintosh auto shutdown (off hot, about 1s). i don't know why but i scared my hdd can be fail if that continue
2. iCloud and brightness: when i start mycomputer, it always ask my update password for icould id and brightness reset to max level
3. My sound: i use AppleALC and LiLu but it not work for me. So i'm using voodooHDA, oh it verry good for me. But onething, i can use HDMI audio and recoder screen with quicktime, it don't recieve system sound although i have been tried use soundflower.
That all error in my hackintosh, I hope to receive help from you
Thanks so much for reading

That's all i have

 

[zukapr]

Hello,

I'm trying to follow your guide but I'm somehow stuck with no audio (got it to work one time but then I tried to not been able to control the volume and stopped working ). I see that at post #1 there's no mention to support for HP Probook 5330m but there's a config.plist for it. Is this model really supported?

Regards,

Gabriel

 

[RehabMan]

Here you are !

Are you saying the card reader at HP18 is functional?

 

[RehabMan]

Hi, I only have one wifi antenna in my 450 G2 and after swapping the connection to the other connector on my wlan card I now have bluetooth but I am unable to connect to any device, be it an apple device or android device. It will connect briefly then disconnect. When I try and connect again i get a message 'Network is Unavailable, Make sure network access is enabled'.

I have removed Android Transfer.

If you need the reporting files again please let me know.

Thanks in advance.

You need to connect antennas to both leads.
Keep in mind the iPhone is not intended to pair. It uses BT4LE. No experience with Android products.

 

[RehabMan]

That's all i have

"Problem Reporting" file are incomplete. Read post #1, "Problem Reporting".
It is obvious from your ioreg that you didn't follow the guide.

 

[RehabMan]

Hello,

I'm trying to follow your guide but I'm somehow stuck with no audio (got it to work one time but then I tried to not been able to control the volume and stopped working ). I see that at post #1 there's no mention to support for HP Probook 5330m but there's a config.plist for it. Is this model really supported?

Regards,

Gabriel

It is supported.
Make sure you read post #1 "Known Problems", "Audio". Must boot without caches, rebuild cache, reboot.
And all queries must have "Problem Reportign" files. Read post #1, "Problem Reporting".

 

[DoHaiSon]

"Problem Reporting" file are incomplete. Read post #1, "Problem Reporting".
It is obvious from your ioreg that you didn't follow the guide.

hic i followed the guide but when use hotpatch dsdt to config.plist, it error voodoops2controller (sometime about 50% it not recieve touchpad) so i'm change config.plist to older version what i use on 10.10.4 and dsdt. All fine but error usb port @@

 

[RehabMan]

hic i followed the guide but when use hotpatch dsdt to config.plist, it error voodoops2controller (sometime about 50% it not recieve touchpad) so i'm change config.plist to older version what i use on 10.10.4 and dsdt. All fine but error usb port @@

Follow post #1 as written.
If you have an issue, provide "Problem Reporting" files as per post #1.

 

[sp-am]

Are you saying the card reader at HP18 is functional?

>> functional ?
I do not know, I only see that it is visible now as USB device. Do you have any proposals for a control program ?