- Joined
- Apr 11, 2020
- Messages
- 17
- Motherboard
- ASUS x299 TUF Mark 2
- CPU
- i7 - 7820x
- Graphics
- RX 5700 XT
- Mac
- Classic Mac
- Mobile Phone
I'm stuck on my Hackintosh build and could use a nudge.
1 - The target hardware: ASUS x299 TUF Mk 2, i7-7820x, M2.NVME - ASUS RX 5700 XT Radeon
2 - My sources:
Unibeast 10.0.1
Catalina from Apple Store (circa April 10th, 2020)
Multibeast 12.1.0
Clover r5112
Kingston Data Traveller USB 3.0, 16 GB
3 - Setting up for Install
I flashed the bios to the latest version from ASUS/AMI = 2.17.1246 (2020)
BIOS Checklist
[x] VT-d = disabled
[ ] CFG-lock { couldn't find it }
[ ] Secure Boot Mode { couldn't find it }
[x] OS Type = other OS
[x] on-board serial port = disabled
[ ] XCHI handoff ... but the Advanced\USB Configuration pane reads in uneditable grey
USB Configuration
USB Module Version 23
USB Controllers: 2 XHCIs
USB Devices: 1 Dave, 1 Keyboard, 1 Mouse
4 - Symptoms
@First Try: At Clover Screen, Boot macOS from Install macOS Catalina
The Apple Logo w/progress bar that started to move then progressively more slowly ... 20 mins later it was full and not doing anything.
@Second Try: After going through all of the BIOS to look for the things I didn't find the first time -- to no avail, I got the same result
[QUESTION] How long should the Apple Logo and progress bar be on the screen? Do I just need to wait for an hour? It is plugged into a USB 3 port on the mother board -- try a different port?
@n-th Try: Spacebar at Clover, [x] -v, verbose & I note that [x] Set Nvidia to VESA was already checked
... the system stops (sooner than what I describe in FirstTry) at the following line
[ PCI configuration end, bridges 11, devices 101 ]
I'm attaching a photo.
@n-th + 1 Try: Spacebar at Clover [x] verbose & [x] Safe mode
... seems to be stopped at the same spot, same final line -- but there are some differences. I attach a second screen shot.
[QUESTION] I'm very keen to get this build to work -- Does anyone see something obviously wrong?
1 - The target hardware: ASUS x299 TUF Mk 2, i7-7820x, M2.NVME - ASUS RX 5700 XT Radeon
2 - My sources:
Unibeast 10.0.1
Catalina from Apple Store (circa April 10th, 2020)
Multibeast 12.1.0
Clover r5112
Kingston Data Traveller USB 3.0, 16 GB
3 - Setting up for Install
I flashed the bios to the latest version from ASUS/AMI = 2.17.1246 (2020)
BIOS Checklist
[x] VT-d = disabled
[ ] CFG-lock { couldn't find it }
[ ] Secure Boot Mode { couldn't find it }
[x] OS Type = other OS
[x] on-board serial port = disabled
[ ] XCHI handoff ... but the Advanced\USB Configuration pane reads in uneditable grey
USB Configuration
USB Module Version 23
USB Controllers: 2 XHCIs
USB Devices: 1 Dave, 1 Keyboard, 1 Mouse
4 - Symptoms
@First Try: At Clover Screen, Boot macOS from Install macOS Catalina
The Apple Logo w/progress bar that started to move then progressively more slowly ... 20 mins later it was full and not doing anything.
@Second Try: After going through all of the BIOS to look for the things I didn't find the first time -- to no avail, I got the same result
[QUESTION] How long should the Apple Logo and progress bar be on the screen? Do I just need to wait for an hour? It is plugged into a USB 3 port on the mother board -- try a different port?
@n-th Try: Spacebar at Clover, [x] -v, verbose & I note that [x] Set Nvidia to VESA was already checked
... the system stops (sooner than what I describe in FirstTry) at the following line
[ PCI configuration end, bridges 11, devices 101 ]
I'm attaching a photo.
@n-th + 1 Try: Spacebar at Clover [x] verbose & [x] Safe mode
... seems to be stopped at the same spot, same final line -- but there are some differences. I attach a second screen shot.
[QUESTION] I'm very keen to get this build to work -- Does anyone see something obviously wrong?