Contribute
Register

Can't complete High Sierra installation - Asus Laptop

Status
Not open for further replies.
It looks like I have all of the required kexts in there. What am I missing?
 
kellee said:
It looks like I have all of the required kexts in there. What am I missing?
Click to expand...

FakeSMC sensor kexts not recommended.
SATA-300-series-unsupportd.kext is deprecated, replaced by SATA-unsupported.kext.
Your copy of USBInjectAll.kext is not the latest.
XHCI-unsupported.kext is missing.
 
I've updated my kexts accordingly, still getting the same result.
 

Attachments

  • CLOVER.zip
    1.9 MB · Views: 44
kellee said:
I've updated my kexts accordingly, still getting the same result.
Click to expand...

For config.plist/SMBIOS, stick with MacBookPro11,1 for now, remove all custom data.
Don't forget to restore the setting you deleted: config.plist/SMBIOS/Trust=true.

Try also with EmuVariableUefi-64.efi and OsxAptioFixDrv-64.efi instead of AptiomemoryFix-64.efi.

Check your BIOS settings too.
 
I was able to install High Sierra onto my USB 3.0 drive. I am able to boot to desktop from it, and use a few apps very slowly. I used Carbon Copy Cloner to start cloning the USB to the SSD, but the system froze after about 40 minutes at about 70% progress. Each time I've booted it back up, it seems to freeze randomly. I have tried completing the transfer with CCC but it cannot run for more than about 5 minutes before freezing. I'm not sure if this is because my USB is 3.0 or if it's something with my Clover configuration.

I had cloned the installation from the 3.0 drive to one of my 2.0 drives, but it can never successfully boot. I get the "exceeded mem limit" errors shown in the screenshot below that do not occur when booting from the 3.0 drive. I'm not sure if it's just because the 2.0 drives I got are amazingly slow and terrible.
7nt87LN.jpg


When I try to boot from the SSD it gives me the error in the screenshot below.
7nt87LN.jpg
 

Attachments

  • CLOVER.zip
    1.9 MB · Views: 124
kellee said:
I was able to install High Sierra onto my USB 3.0 drive. I am able to boot to desktop from it, and use a few apps very slowly. I used Carbon Copy Cloner to start cloning the USB to the SSD, but the system froze after about 40 minutes at about 70% progress. Each time I've booted it back up, it seems to freeze randomly. I have tried completing the transfer with CCC but it cannot run for more than about 5 minutes before freezing. I'm not sure if this is because my USB is 3.0 or if it's something with my Clover configuration.

I had cloned the installation from the 3.0 drive to one of my 2.0 drives, but it can never successfully boot. I get the "exceeded mem limit" errors shown in the screenshot below that do not occur when booting from the 3.0 drive. I'm not sure if it's just because the 2.0 drives I got are amazingly slow and terrible.
7nt87LN.jpg


When I try to boot from the SSD it gives me the error in the screenshot below.
7nt87LN.jpg
Click to expand...

You already installed? Or not?
 
I was able to install High Sierra onto my USB 3.0 drive. I am able to boot to desktop from it, and use a few apps very slowly. I used Carbon Copy Cloner to start cloning the USB to the SSD, but the system froze after about 40 minutes at about 70% progress. Each time I've booted it back up, it seems to freeze randomly. I have tried completing the transfer with CCC but it cannot run for more than about 5 minutes before freezing. I'm not sure if this is because my USB is 3.0 or if it's something with my Clover configuration.

I had cloned the installation from the 3.0 drive to one of my 2.0 drives, but it can never successfully boot. I get the "exceeded mem limit" errors shown in the screenshot above that do not occur when booting from the 3.0 drive. I'm not sure if it's just because the 2.0 drives I got are amazingly slow and terrible.

When I try to boot from the SSD it gives me the error in the screenshot above.
 
kellee said:
I was able to install High Sierra onto my USB 3.0 drive. I am able to boot to desktop from it, and use a few apps very slowly. I used Carbon Copy Cloner to start cloning the USB to the SSD, but the system froze after about 40 minutes at about 70% progress. Each time I've booted it back up, it seems to freeze randomly. I have tried completing the transfer with CCC but it cannot run for more than about 5 minutes before freezing. I'm not sure if this is because my USB is 3.0 or if it's something with my Clover configuration.

I had cloned the installation from the 3.0 drive to one of my 2.0 drives, but it can never successfully boot. I get the "exceeded mem limit" errors shown in the screenshot above that do not occur when booting from the 3.0 drive. I'm not sure if it's just because the 2.0 drives I got are amazingly slow and terrible.

When I try to boot from the SSD it gives me the error in the screenshot above.
Click to expand...

Add EmuVariableUefi-64.efi to drivers64UEFI. It might help.
 
RehabMan said:
Add EmuVariableUefi-64.efi to drivers64UEFI. It might help.
Click to expand...
Added that, same result as before. System freezes after just a few minutes of running CCC.
 

Attachments

  • CLOVER.zip
    1.9 MB · Views: 55
Status
Not open for further replies.
Copyright © 2010 - 2024 tonymacx86 LLC
Back
Top