[Guide] Native Intel UHD630 Graphics support in macOS 10.13.6

[ben9923]

No need to set An specifying value on ig_platfrom or Fake ID?

If you can boot (and you probably can) - no need, at least for installation purpose.
Just make sure you fill all of the 15,2 SMBIOS data in your config.plist, then boot to Recovery and choose to reinstall macOS.

 

[rcc622]

Ok, I will.
Question. The guide that I used to install OSX was installed osx via clover by RehabMan but I don't know if I need to use an exact value on DVMT-prealloc memory. I set it on 64mb. Is this ok?

And I use one of his config.plist
Config.620,630...plist

 

[ben9923]

Ok, I will.
Question. The guide that I used to install OSX was installed osx via clover by RehabMan but I don't know if I need to use an exact value on DVMT-prealloc memory. I set it on 64mb. Is this ok?

And I use one of his config.plist
Config.620,630...plist

64MB should be fine for FHD.
Start with the config for 620/630, but remove FakeID and ig-platform-id entries (+KBL patches in KextsToPatch).
Of course, you must fill SMBIOS data for MBP15,2. Also remember the -no_compat_check flag.

 

[rcc622]

(+KBL patches in KextsToPatch).

Ok, I will remove theme. Thanks. I will keep in touch

[UPDATE]

After did what you said im still unable to acces to recovery partition via clover and neither boot to my OSX . I attach my PRF to you if its help. Meanwhile I will try to get acceleration via another method (spoof CFL to KBL)

[update 2]

PR FILE ATTACHED

 

[RehabMan]

Ok, I will remove theme. Thanks. I will keep in touch

[UPDATE]

After did what you said im still unable to acces to recovery partition via clover and neither boot to my OSX . I attach my PRF to you if its help. Meanwhile I will try to get acceleration via another method (spoof CFL to KBL)

[update 2]

PR FILE ATTACHED

You should specify FakeID/IntelGFX and Graphics/ig-platform-id... otherwise, you're leaving the choice to defaults in Clover.

 

[rcc622]

You should specify FakeID/IntelGFX and Graphics/ig-platform-id... otherwise, you're leaving the choice to defaults in Clover.

THANKS REHABMAN now I can boot. I used ig_platform 0x3E920009 and FAKEID 0x3E928086

 

[RehabMan]

THANKS REHABMAN now I can boot. I used ig_platform 0x3E920009 and FAKEID 0x3E928086

Not possible to verify you have anything working without PR files as per FAQ.

 

[rcc622]

Not possible to verify you have anything working without PR files as per FAQ.

I was following the old method as ben9923 recommended

Try the 'old' method in post #1, it should still work.

The recovery partition download the latest version of OSX HS. after that the computer restart by itself to launch the installer but then I had a boot loop. I try boot via verbose but I didn't catch any valuable information.

I attaches the PR FILE and a few pictures about verbose (the photos are named according to their order of appearance)

 

[RehabMan]

I was following the old method as ben9923 recommended


The recovery partition download the latest version of OSX HS. after that the computer restart by itself to launch the installer but then I had a boot loop. I try boot via verbose but I didn't catch any valuable information.

I attaches the PR FILE and a few pictures about verbose (the photos are named according to their order of appearance)

Your ioreg proves that QE/CI is NOT working.

 

[rcc622]

Your ioreg proves that QE/CI is NOT working.

and what does it mean? does it have fix?

NOTE
I had to delet the kext patch KBL graphics frame buffer