- Joined
- Jun 8, 2016
- Messages
- 1
- Motherboard
- ASUS B75M-A
- CPU
- i7-7700K
- Graphics
- ASUS GTX 750-Ti-PH-2GD5
- Mac
- Classic Mac
- Mobile Phone
I was looking for some guide or info to install successfully MacOS 10.12.6 on this board but all the info was not too useful so, trying different configurations finally I got installed and use it almost 100%.
This is my hardware info:
MoBo: Asus B75M-A (specs here: http://www.asus.com/Motherboards/B75MA/#specifications)
Processor: Intel Core i7-3770K
Graphics: Nvdia GT750 Ti / iGPU HD 4000 (ML Works natively)
RAM: Kingston HyperX Fury Ram DDR3 1866MHz 8GB x2 = 16GB
HDD: Sandisk Extreme Pro 960GB SATA3. (Write: 515MB/s Read: 550MB/s)
Setting up the BIOS:
As first, load default values and then change all next options:
· Under Advanced \ SATA Configuration set SATA Mode Selection to AHCI (Configured as default but ensure it is set to AHCI)
· Under Advanced \ SATA Configuration set all Hot Plug to Enabled (Except the one you use for the OSX boot drive, may be used as optional)
· Under Advanced \ System Agent Configuration \ Graphics Configuration set Primary Display to iGPU and iGPU Memory to 96MB (Needed to be recognized by ML, Chimera or Chameleon)
· Under Advanced \ USB Configuration set EHCI Hand-off to Enabled
· Under Advanced \ APM set Restore AC Power Loss to Power On and Power On By PCIE to Enabled (PCIE is for Wake-on-Lan)
· Under CPU Virtualization Technologies must be set to disabled.
Installation and setup:
Step1. Boot using Unibeast 7.1.1 to create USB stick.
Step2. Use Clover Configurator 4.46.0 to set your config.plist:
-v (Verbose) / PCIRootUID=0 / dart=0 / nv_disable=1 to reach successfully installation screen
Step3. Run MultiBeast 9.1.0(Sierra), Select the next options:
This is my hardware info:
MoBo: Asus B75M-A (specs here: http://www.asus.com/Motherboards/B75MA/#specifications)
Processor: Intel Core i7-3770K
Graphics: Nvdia GT750 Ti / iGPU HD 4000 (ML Works natively)
RAM: Kingston HyperX Fury Ram DDR3 1866MHz 8GB x2 = 16GB
HDD: Sandisk Extreme Pro 960GB SATA3. (Write: 515MB/s Read: 550MB/s)
Setting up the BIOS:
As first, load default values and then change all next options:
· Under Advanced \ SATA Configuration set SATA Mode Selection to AHCI (Configured as default but ensure it is set to AHCI)
· Under Advanced \ SATA Configuration set all Hot Plug to Enabled (Except the one you use for the OSX boot drive, may be used as optional)
· Under Advanced \ System Agent Configuration \ Graphics Configuration set Primary Display to iGPU and iGPU Memory to 96MB (Needed to be recognized by ML, Chimera or Chameleon)
· Under Advanced \ USB Configuration set EHCI Hand-off to Enabled
· Under Advanced \ APM set Restore AC Power Loss to Power On and Power On By PCIE to Enabled (PCIE is for Wake-on-Lan)
· Under CPU Virtualization Technologies must be set to disabled.
Installation and setup:
Step1. Boot using Unibeast 7.1.1 to create USB stick.
Step2. Use Clover Configurator 4.46.0 to set your config.plist:
-v (Verbose) / PCIRootUID=0 / dart=0 / nv_disable=1 to reach successfully installation screen
Step3. Run MultiBeast 9.1.0(Sierra), Select the next options: