No Sound - Realtek ALC AppleHDA [Guide]

[RedBedford]

Installing Clover on the ssd has no risk.

If there is a problem, boot with the usb.

Aha! Thanks very much! I'll try tonight!

 

[RedBedford]

No audio until the system boots from the system disk. Fix boot and post files from successful boot.

I have installed clover on the SSD successfully now, and currently have the same problems as before in terms of audio, but now the USB is not necessary to boot. What am I missing? My original post with all the details can be found here.

 

[toleda]

all the details can be found here

Useless.
Did you install audio?
Attach new files.

 

[RedBedford]

Useless.
Did you install audio?
Attach new files.

I attached my EFI directory compressed, that should show my config.plist and kexts installed. I'm on 10.10.5. Not sure what else is needed as the old information is useless apparently.

 

[toleda]

Not sure what else is needed as the old information is useless apparently

Old info is useless because you restarted (different with each boot) and booted off a different EFI partition
A few of the requested files is as useful as none.
See Problem Reporting, Post #1; attach all requested files

 

[RedBedford]

1. I installed Yosemite 10.10.5 back in June 2015 using the recommended list of parts here on this website. Everything worked well except for occasional freezes, but recently a freeze came and it would not boot back up. I keep a clover usb with El Capitan around in case chameleon stops working (it did). I used clover to boot into the OS and everything works great except for the audio. I copied the efi directory from the usb to the ssd and am now running solely on the SSD. There are no audio output devices listed. I've attempted to plug it into the front panel of my Corsair 500R, as well as into the green port on the (listed below) motherboard.
2. My build is Yosemite 10.10.5 on a computer held in a Corsair 500R that is running on an Intel i7 4790k with 16GB of Crucial Ballistix Tactical RAM on a Gigabyte GA-Z97X-UD5H-BK motherboard and all graphics are handled by my Gigabyte GTX 960 Windforce 2GB.
   1. MOTHERBOARD: Gigabyte GA-Z97X-UD5H-BK
   2. RAM: Crucial Ballistix Tactical 16GB
   3. PROCESSOR: Intel core i7 4790k
   4. GRAPHICS: Gigabyte GTX 960 Windforce 2GB
   5. CASE: Corsair 500R
   6. OSX VERSION: Yosemite 10.10.5
3. I attempted this guide the other day, but was unable to get it to work.
4. Attached IOReg (joshuabedford.ioreg)
5. Not found
6. Not found
7. I went to Console/All Messages. Searched for 'kernel sound' nothing came up. I Probably misunderstood.
8. audio.jpg attached
9. possibly irrelevent but It WAS installed just (i think) not in use anymore
10. Attached EFI/EFI/CLOVER/config.plist & Not sure what DPCIManager/misc/BootLog is
11. Headphones
    1. AKG K240 Mk ii headphones
       
    2. Front case port
    3. No Output devices

 

[toleda]

I attempted this guide the other day, but was unable to get it to work.

This thread supports Realtek ALC AppleHDA/Post #1 methods only.
Remove other installed audio methods
Installl audio with a method from the linked thread
Attach new files.

 

[RedBedford]

This thread supports Realtek ALC AppleHDA/Post #1 methods only.
Remove other installed audio methods
Installl audio with a method from the linked thread
Attach new files.

Is MultiBeast what you use with clover to install drivers?

 

[toleda]

Is MultiBeast what you use with clover to install drivers?

I use cloverALC, MultiBeast is fine.

 

[RedBedford]

I use cloverALC, MultiBeast is fine.

I ran the install for the Realtek Driver (multibeast.jpg attached), and restarted, but still no audio. I've attached the (I believe) necessary files. Thanks for your time!