Hangs on BlueTooth while loading....

[thomasmb]

I have Sabertooth X79 running BIOS 4701. Have tried 4608 and 4801. Still can't get past this step. [IOBluetoothHCIController][start] -- completed. Can't find where to shut off Secure Boot. Option to run Other OS has been select. Also have chosen Optimized Defaults. VT-D shows to be Disabled.

Boot Flags Used:
-x
npci=0x2000
GraphicsEnabler=Yes
maxmem=4096

CPU: Intel Core i7 4930K, 3.4GZ
Motherboard: ASUS Sabertooth X79
RAM: 32GB Crucial Balistix (8X4)
Solid State Drive: Samsung 250GB SSD 840

Help Me! Help Me! Help Me!!!!

 

[cmn699]

I have Sabertooth X79 running BIOS 4701. Have tried 4608 and 4801. Still can't get past this step. [IOBluetoothHCIController][start] -- completed. Can't find where to shut off Secure Boot. Option to run Other OS has been select. Also have chosen Optimized Defaults. VT-D shows to be Disabled.

Boot Flags Used:
-x
npci=0x2000
GraphicsEnabler=Yes
maxmem=4096

CPU: Intel Core i7 4930K, 3.4GZ
Motherboard: ASUS Sabertooth X79
RAM: 32GB Crucial Balistix (8X4)
Solid State Drive: Samsung 250GB SSD 840

Help Me! Help Me! Help Me!!!!

Assuming you have a a perfectly well created Unibeast Yosemite USB Installer, here are some suggestions:

• First try booting the Unibeast Yosemite USB Installer without the PCIE Add-on Video card and in the
• BIOS setup try choosing (if not already done so) :

IGD: Selected
SATA Mode AHCI
​

HPET :Enabled if there is a HPET Mode option make it 64Bit
​

Legacy USB Support Enabled
​

Legacy USB 3.0 Support :Enabled
​

Intel xHCI Mode: Auto [ NEVER SMART Auto]
​

EHCI Hand-off: Enabled
​

For Boot flags for Unibeast Yosemite USB Installer:

-v -x npci=0x2000 GraphicsEnabler=No PCIRootUID=1 -f
(some of the above may be an 'overkill' without harm)

Hopefully you should be able to overcome the block at "BlueTooth..." which is from lack of proper Video kext.

Please post in details and with Screen capture image if there is problem.

Good luck

Regarding Secure boot: Depending on the motherboard’s BIOS/EFI firmware, the Secure Boot option will be found on the “Boot”, “Security”, or “Authentication”

I suspect it to be under Boot menu on your board's BIOS settings

 

[P1LGRIM]

I have Sabertooth X79 running BIOS 4701. Have tried 4608 and 4801. Still can't get past this step. [IOBluetoothHCIController][start] -- completed. Can't find where to shut off Secure Boot. Option to run Other OS has been select. Also have chosen Optimized Defaults. VT-D shows to be Disabled.

Boot Flags Used:
-x
npci=0x2000
GraphicsEnabler=Yes
maxmem=4096

CPU: Intel Core i7 4930K, 3.4GZ
Motherboard: ASUS Sabertooth X79
RAM: 32GB Crucial Balistix (8X4)
Solid State Drive: Samsung 250GB SSD 840

How are you connected to your monitor ?
VGA is not supported - Use a digital connection (DVI or HDMI) on your graphics card.

You should boot with nv_disable=1 until you have installed the web drivers.

This thread may help you : http://www.tonymacx86.com/showthread.php?t=161256

 

[thomasmb]

How are you connected to your monitor ?
VGA is not supported - Use a digital connection (DVI or HDMI) on your graphics card.

You should boot with nv_disable=1 until you have installed the web drivers.

This thread may help you : http://www.tonymacx86.com/showthread.php?t=161256

nv_disable=1 did the trick. On to the next step.....

As you can recognize.. This is my first Hackintosh. I am so pumped!

Thanks Guys!