- Joined
- Jun 17, 2019
- Messages
- 11
- Motherboard
- X299X Designare 10G
- CPU
- I9-9980XE
- Graphics
- RX5700XT, Radeon VII
- Mac
How about BCM94360NG on the board? Does it work with OOB?
The BIOS error appears when there are two drives (could be a USB) with bootloader at boot, this board BIOS is absolute rubbish, that much I can tell.Thank you for your effort for X299X Designare 10G. It's very difficult for me, but I'm following the guide. Clover is being used for build. After setting the Disable Block side = Enable, it was possible to install, but when booting, it encountered a bios error screen. Go out without saving after entering BIOS, I can use it normally, but is there a way to solve it?
And another problem is that CPU clocks and memory clocks are not normal. XMP is also not applied and is fixed at 2,300Mhz. The CPU clock is about 3800. I'd like to know how to turn it back to its basic state and how to adjust it.
I installed it using Dolgarenan's Clean EFI, added ACPI, added device attributes, and created an aml file with the code using Maciasl and put it in clover/acpi/patched.
Most BCM chipsets work with BRCMFixup kexts from acidanthera, not exactly OOB but closeHow about BCM94360NG on the board? Does it work with OOB?
Her is the patched BIOS-file for MSI X299 SLI PLUS, latest version. Use the Flash button on the backside... leave the MSR Lock at default (i think "Enable"). The EFI-Folder is for 10C and quite small, but it should boot without specific problems (perhaps you have to try with or without npci=0x2000). For post you need the Ethernet-drivers (Smalltree and IntelMausi).Well done to all in getting 10900X and MSI X299 board booting/working. Can you share UEFI and other relevant topics. I have MSI X299 SLI plus and 10900X with no progress beyond "++++++++" using Clover. Thanks!
Hey there Tonzone. Wow! I am speechless at your generosity!. BIOS flash worked fine. EFI folder booted super fast!
Ethernet kexts loaded. Many many thanks for your help here. Please let me know which entity I can donate some funds.
Fantastic work and maximum respect! Best regards, Nick
The BIOS error appears when there are two drives (could be a USB) with bootloader at boot, this board BIOS is absolute rubbish, that much I can tell.
The issue comes when:
Check the above and report back, alternatively if you still have issues just upload your EFI without themes nor IDs and such.
- Two bootloader drives at boot.
- You have a system drive with bootloader installed in your board and want to boot from a USB with bootloader too, lets say a Clover BL. You have to make sure that once you have the system installed you don't try to boot from an external source, unfortunately this board will just KP and send you the message you posted
- Incorrect BIOS settings.
- Double check your BIOS settings, there might be something wrong, BIOS version 3b is the most stable yet.
- Make sure Above 4G is enabled.
Hi @tonzoneHi zzmadd, a good entry level tip is the MSI X299 Pro (https://de.msi.com/Motherboard/X299-PRO), you only have to use a patched UEFI (I have it, if you need). I have got it nearly perfect with an RX 580 and 590, and a flashed Alpine Ridge TB Card (1000 thanks to scottkendall). Tested with 9960X, 10900X, 9940X.
@oli.mathieu
I have tested a 10900X successfully with the above mentioned MSI X299 Pro and the Asus Prime X299 A-II, both with the magic of Loloflatsix and UEFIpatch. Not much more complicated than the previous X299´s.
Hi @tonzone thanks for the detailed reply. (For some reasons your reply didn't show up in the notifications).@zzmadd
I think it´s a matter of taste... I like the MSI, it´s clear, no blingbling, it just works ;-)
It has two LAN ports, one is a RTL8125; it´s without function at the moment, but the fabulous Mausi is working on it: https://github.com/Mieze/LucyRTL8125Ethernet).
I have done short tests with TB and it seems to work very very good, I´ve tested a flashed Alpine Ridge and the MSI TBM3. It has the newest USB3.2 with 20 Gbps (ASM3242), but there are no drivers in macOS, it works as USB2 (maybe with later Catalina-versions?). But it also has an ASM3142 which is working nativ. 15.470 points with GB5/9940X (see below).
The Asus Prime A-II has only 1 LAN port, but 3 x m.2 ports, the MSI 2 x.
For both boards we have to patch the UEFI. Yo can use the EFI-folder from this post as basic: https://www.tonymacx86.com/attachments/efi-zip.465613/ - you only have to add the network drivers, and if you want a board-specific USB-Kext.
View attachment 465902