ga-x99-ud4 , 5820K, gt740- can't get into instalator please help

[blendaman]

GA-X99-UD4,5820K,EVGA GT740- can't get into instalator please help

Hello Guys! so here are the spec:

i7 5820k
ga-x99-ud4 rev 1.0 Bios f11
EVGA gt740 Sc 4GB
16gb g.Skill Ripjaws

SSD plextor
Storage 1tb WD
h105

i have set all bios features to "optimised" and added something like this:
manual on XHCI and idstable hand-of
sata in AHCI mode

next i have follow the famous Bob Roche guide on YT (from InsaneCultist thread) what is popular here during installation of X99

when i was paching using Stinga11 tip i have issue that after commands in terminal i did not have to put the password and thats was different than in tutorial video < maybe this is the clue?

next i have booted from usb and all the time i have stuck on apple logo , sometimes few pixels was loaded and sometimes nothing.

so i have start using different flags like:


1:

npci=0x300 -f -x -v graphicsenabler=no

resoult:


2:

npci=0x300 -f -x -v

resoult:



3:

npci=0x3000 PCIRootUID=1 -f -x -v

resoult:



4:

npci=0x3000 maxmem=4096 PCIRootUID=1 -f -x -v


resoult:



also have tired all of those flags alone , in different combination also have used all other what i could find here in forum.

now have no idea what to do and I'm afraid that i must buy gtx9xx to make this **** working

i gonna make fresh unibeast usb yosemite stick just in case that maybe this copy got any bug :/

i bought this evga card due to the buyers guid that i found here so there should be some fix or way to solve this? right ?

Do You have any ideas what could i do ?

Thanks in Advance!

 

[BreBo]

Did you try to add nv_disable=1 to your boot flags?

Your graphics card probably needs the Nvidia web drivers.

 

[blendaman]

yeah i have tried, but not sure it was used alone or with something other. Gonna try it out Thanks !

 

[BreBo]

Try to boot with npci=0x2000 nv_disable=1 -f -x -v

 

[blendaman]

Try to boot with npci=0x2000 nv_disable=1 -f -x -v

Hey! i have tried this and no success

also i have check those:

1:
nv_disable -f -x -v

and resoult is:

2:
nv_disable npci=0x3000 -f -x -v

resoult:

3:

nv_disable=1 npci=0x2000


4:

-f -x -v
:

also tried some kind of : dart=0 + nv_disable , and some others

and have no idea what else i can do ?

 

[blendaman]

any idea anyone ?

 

[P1LGRIM]

any idea anyone ?

Please read the Rules :

Profiles need to contain at least your primary system to assist others with helping you

Connect to your monitor with a digital connection - DVI or HDMI - VGA is not supported.

Try booting with :

dart=0 npci=0x2000 nv_disable=1 -f -x -v

 

[blendaman]

Please read the Rules :


Connect to your monitor with a digital connection - DVI or HDMI - VGA is not supported.

Try booting with :

dart=0 npci=0x2000 nv_disable=1 -f -x -v

Thanks for info , i have updated profile,

so monitor is conected via DVI , i have tried this what YOu sugested and here are the resoults:

 

[Adrian B]

Are you using a USB 2 flash drive? And is it inserted in to one of the rear I/O USB 2 ports? There is a number of people that have installed with similar hardware, used similar boot flags and been successful.

http://www.tonymacx86.com/search.php?googleSearch=ga-x99-ud4

Check the Pre - installation requirements in this thread:
http://www.tonymacx86.com/yosemite-...mite-10-10-x-full-temp-guide-100-working.html

Pre installation requirements:
Go into bios, use "load optimized defaults" , Set XHCI to Manual, disable XHCI hand off (carefully checked these settings) *Update, setting XHCI to Auto seems to work OK too, just not "Smart Auto"*

Hopefully there is a minor instruction that you have missed or a different setting that has been used that will make this all come to life for you.

 

[ninetto]

try:

cpus=1 flag.

good luck,
ninetto