Clover update stopped working system

[GreyWolfRon]

If you have a USB port map, I would check it is correct. As the prohibited sign doesn't normally appear when you have a correctly configured USBPorts.kext or USBMap.kext. Assuming you were using one of the active ports from the USB map when the error occurred.

I have checked every single port with 2 and 3. Here is where the USB pen is installed.

 

[Feartech]

I have checked every single port with 2 and 3. Here is where the USB pen is installed.

View attachment 576049

you have set them all to internal.... that is incorrect

The New Beginner's Guide to USB Port Configuration

Important Update: June 2023 From Big Sur 11.3 on the built-in OpenCore XhciPortLimit quirk no-longer worked as described. This became a known "bug", though in reality it was Apple changing their internal code, making a simple "peek and poke" to keep it operating, a difficult task. However, with...

www.tonymacx86.com

 

[GreyWolfRon]

you have set them all to internal.... that is incorrect

The New Beginner's Guide to USB Port Configuration

Important Update: June 2023 From Big Sur 11.3 on the built-in OpenCore XhciPortLimit quirk no-longer worked as described. This became a known "bug", though in reality it was Apple changing their internal code, making a simple "peek and poke" to keep it operating, a difficult task. However, with...

www.tonymacx86.com

I did not set them. That is how they all came up when I install the USB 2 and USB 3. I only deleted 5 lines from within the Hackintool.

I have a mayday

I was following the install of the IOSkyFamily kexts and all was going good until I used the "openCore Patcher" the patcher said it did what it was supposed too and to reboot. Now I get to about 50 of the way, then it locks up.

I tried to use the USB stick with the backup EFI on it. Same thing. I have tried reseting the NVRAM and rebooting from the USB several times. Nothing.

Lost!

 

[GreyWolfRon]

you have set them all to internal.... that is incorrect

The New Beginner's Guide to USB Port Configuration

Important Update: June 2023 From Big Sur 11.3 on the built-in OpenCore XhciPortLimit quirk no-longer worked as described. This became a known "bug", though in reality it was Apple changing their internal code, making a simple "peek and poke" to keep it operating, a difficult task. However, with...

www.tonymacx86.com

I did follow that process for the mapping.

 

[GreyWolfRon]

Ready to scream! I have been going for 5 days on this. All was going ok until the patcher ran.

 

[GreyWolfRon]

Here is the last log from after trying to go back to my USB boot

 

[GreyWolfRon]

@Edhawk @Feartech

I was able to turn -v back on and this is what I get on the halt.

 

[GreyWolfRon]

Okay, I was able to find the disk that had my Mojave build on and the Clover EFI. I booted from that and was able to get the disk0 to boot. I cannot run many apps because they say that Mojave is to old. But I am able to boot the EFI from the other drive disk1 with the Sonoma on it.

I do not know what the openCore patcher changed to cause the faults. But I suspect they are in the Library folder of the drive.

I am going to call it a night and try to get some sleep.

 

[Feartech]

I did not set them. That is how they all came up when I install the USB 2 and USB 3. I only deleted 5 lines from within the Hackintool.

I have a mayday

I was following the install of the IOSkyFamily kexts and all was going good until I used the "openCore Patcher" the patcher said it did what it was supposed too and to reboot. Now I get to about 50 of the way, then it locks up.

I tried to use the USB stick with the backup EFI on it. Same thing. I have tried reseting the NVRAM and rebooting from the USB several times. Nothing.

Lost!
View attachment 576061

exactly, you need to use the drop down option to select usb2/usb3 etc

 

[GreyWolfRon]

exactly, you need to use the drop down option to select usb2/usb3 etc

Well, if I can get back to there I will do that. The patcher totally hosed the drive. I was able to get back into the disk0 after locating the drive with my backup clover EFI and got that up. I can boot on that drive and mount the EFI for the disk1 if I can find out what the patcher did to hose and fix it.

Any ideas?