- Joined
- Nov 18, 2016
- Messages
- 3
- Motherboard
- Asus Prime B450m-a
- CPU
- Ryzen 2600
- Graphics
- RX 580
Hi everybody,
I'll probably need your help... I'm trying to install Sierra on a pretty old configuration...
- Gigabyte GA-EX58 UD3R
- Intel Xeon X5880
- NVidia Geforce Quadro FX4800
In the BIOS settings I've done the following
- deactivated Hyperthreading
- limited on 1 CPU core
- deactivated Virtualization technology
- HPET support activated & on 64bit
I use the following kexts:
- FakeSMC (from my previous Yosemite installation)
- IOPCIFamily (from my MacBookAir running Sierra)
- IOUSBHostFamily (from my MacBookAir running Sierra)
- NullCPUPowerManagement (also from )
- NVDAStartup (from my previous Yosemite installation)
- RealtekRTL8111 ()
- USBInjectAll (from my MacBookAir running Sierra)
- VoodooTSCSync (from Multibeast)
Most of them because I had some trouble before. Is it a problem where I got the kexts from or are they probably not compatible?
... with these boot flags:
GraphicsEnabler=Yes because the X5880 has no onboard graphic chip afaik...? So I assume there is no chance to boot into with nv_disable=1, isn't it?
It shuts down with the following messages:
... & then it shuts down. And nothing that I tried helps me to get over this message. Probably it should say something like "Like up on..." – and what about the AppleUSBHostPort disconnect? Does the installation loses the connection to the USB flash drive? I tried nv_disable=1 several times (because in a different topic here I read to do so) just to see if it changes anything, but the problem remains the same.
Has anyone an idea and can help here?
Sven
I'll probably need your help... I'm trying to install Sierra on a pretty old configuration...
- Gigabyte GA-EX58 UD3R
- Intel Xeon X5880
- NVidia Geforce Quadro FX4800
In the BIOS settings I've done the following
- deactivated Hyperthreading
- limited on 1 CPU core
- deactivated Virtualization technology
- HPET support activated & on 64bit
I use the following kexts:
- FakeSMC (from my previous Yosemite installation)
- IOPCIFamily (from my MacBookAir running Sierra)
- IOUSBHostFamily (from my MacBookAir running Sierra)
- NullCPUPowerManagement (also from )
- NVDAStartup (from my previous Yosemite installation)
- RealtekRTL8111 ()
- USBInjectAll (from my MacBookAir running Sierra)
- VoodooTSCSync (from Multibeast)
Most of them because I had some trouble before. Is it a problem where I got the kexts from or are they probably not compatible?
... with these boot flags:
Code:
-v dart=0 GraphicsEnabler=Yes kext-dev-mode=1
GraphicsEnabler=Yes because the X5880 has no onboard graphic chip afaik...? So I assume there is no chance to boot into with nv_disable=1, isn't it?
It shuts down with the following messages:
Code:
[...]
error 0xe00002db opening polled file
000033.552960 AppleUSBEHCIPort@fd200000: AppleUSBHostPort::disconnect: persistent enumeration failure
kern_open_file_for_direct_io(28)
kern_open_file_for_direct_io tool 15ms
Ethernet [RealtekRTL8111]: Link down on en0
... & then it shuts down. And nothing that I tried helps me to get over this message. Probably it should say something like "Like up on..." – and what about the AppleUSBHostPort disconnect? Does the installation loses the connection to the USB flash drive? I tried nv_disable=1 several times (because in a different topic here I read to do so) just to see if it changes anything, but the problem remains the same.
Has anyone an idea and can help here?
Sven