sleep doesn't work

Hello everyone, I have an issue with sleep mode. I've installed Ventura and Sonoma, but sleep doesn't work properly. Shortly after sleep is initiated, there's always an instant wake. When I check it with the command log show | grep -i "wake reason" via terminal, it gives output like below...

Hi all, I have been using my hack for almost 2 years and all patches were done properly. For some unknown reason, the S3 sleep no longer work after upgrade to monterey 12.3 and OC0.7.9. I did not anticipate this and did the upgrade in one go. As a result, I cannot tell whether it is the...

Hi, I have an issue that my build wakes up shortly after I put it to sleep. First, the system goes into sleep after asking it to, the screen goes dark, and shortly after, the fans stop spinning, and the RGB LEDs on different components shut down (except my RAM RGB:s, which stay turned on). But...

Hello! I finally managed to make my system work flawlessly except sleep/wake. I have more than 15 ports used because I 've got a bluestork usb hub 7 ports. I don't want to remove my hub for fengshui reasons (:mrgreen:) Hibernate mode is 3 Power management Enabled in bios. SSDT(s) taken on...

After updating to 11.2 I suddenly couldn't get the hack to sleep—a familiar problem from many updates. The screen would go black and after a couple of seconds come back on. In Activity Monitor the only thing shown to prevent sleep was WindowUser and that is a vital core component, therefore no...

(For those who had talked with me before from the other conversation, I decided to start a new conversation because we can focus directly on my problem here) Hi everyone. Recently I've installed macOS Catalina on my laptop. I run OpenCore as my Bootloader. I have a Dell Inspiron 14 7472 (bought...

Hi all, I had a fully functionning Hackintosh setup running Mojave 14.4.6 and got the notification that a new Security Update 2020-002 was available. I've installed it but since then, the sleep functionnality isn't working anymore. As soon as I put my computer to sleep (Cmd+Option+Eject), it...

Hi there, I've been setting up my hackintosh for the last 3 days and I could say it's working on Catalina. The only thing that's annoying is when I need to put my machine in sleep mode or to shutdown it, the shutdown doesn't really works (if I press a key on my keyboard, it starts) and the...

I have a new build I just created and I have the dreaded can't wake from sleep issue. I got everything working with UniBeast and Clover.. but can't seem too get the machine to wake from sleep. I have looked into mapping the USB ports to address the issue, with no luck. I have included the...

Hello there, I set up a Hackintosh and almost everything seems to work well except the sleep mode. When I click on "Sleep", the displays switch off and 10s later shortly before sleeping the fans of my Vega 64 get very loud for about 3 seconds. After that, everything is silent for 1-2 seconds and...

FIXED :D Removed the _PWR methods of XDCI & HDAS in my DSDT and changed the _DSM methods to XDSM via Clover. I don't know which one of them fixed it or if both together were needed ¯\_(ツ)_/¯. But regardless as soon as I activated Thunderbolt 3 in UEFI It worked:D. I know this thread is only...

I was using Mojave 10.14.2 on my old build for sometime. https://www.tonymacx86.com/threads/success-gigabyte-ga-h170-d3h-intel-tm-core-r-i3-6100-corsair-8gb-ram-hd-530-sierra-10-12-6.229045/ Recently I changed my SSD and did a clean installation of Mojave 10.14.6 . Everything works fine except...

Hello friends, Has past a while since i didn't pulled my hair out, yet here I am. So, with what to begin... Using my intel i7-4790K on GA-Z97X-UD5H motherboard, sleeping function worked almost OOB, without disabling any "hibernationmode", without too much headache. Now using the same intel on...

So, successful Mojave install after several attempts on my ssd, cloned to NVME to get HFS. Problems getting sleep to work. Goes to sleep fine, when wakes up, crashes after several seconds and then reboots. I see 100 different topics on this forum, have searched youtube etc., videos, tried ~30...

So this was working fine awhile ago. I did get a new mouse (so new hardware) and I also disabled sleep via the Energy System Preferences for one day (I was doing a large file transfer and didn't want it interrupted. I'm not certain if the update to 10.13.6 was about that same time too or not...

CPU/GPU PM seems to be working as x86PlatformPlugin and AGPM both run with PluginType=True. Upon putting the laptop to sleep, it just reboots. System hardware details:- MoBo - MSI GV62 (HM370) CPU - i7 8750H GPU - Nvidia gtx 1060 (disabled), UHD630 (full acc.) Screen - 1920x1080 wide view full...

So I got a vanilla install working and a lot of things are working. Unfortunately I cannot get sleep to work at all which is really important for my setup. I have read and seen many threads on this forum with similar builds and have not had success. Sometimes after wake I have no signal, but my...

Hello All, I have a Sierra OS 10.12.6, Skylake Core i5 6500, with ASRock Z170, an EVGA 1050, and the lastest version of clover (4558). I've gotten pretty much everything to work except for sleep. When putting the computer to sleep, it will go dark and fans will stay on for about a minute...

When I put my machine to sleep, the display turns off, but then it restarts back to the Clover boot screen a few seconds later. Following the restart, I get these results in the syslog when I run: log show --style syslog | fgrep "sleep" 2018-06-15 11:06:06.159494-0600 localhost kernel[0]...

I was able to finally upgrade to HS but now I am not able to put it to sleep. Both my monitors go black but the computer still works, everything spins on. When I double click the monitors come to life instantly. Also, i would like to generate a new config.plist but i am not really sure how to do...