Excellent - glad you got it all working!! I don't use wi-fi on my desktops - all hard-wired - so didn't run into this problem. Will keep it in mind if I have to make any changes.
Hmmm. OK:
Launch CSM - Enabled. Boot device control - UEFI only.
Boot from Network - Ignore.
Boot from Storage Devices and PCI-E/PCI devices - UEFI only.
Under Advanced/PCI Subsystem, I have: Above 4G decoding - Enabled, Re-size BAR support - Auto, IOV support - Disabled
Under System...
Yeah...I had this same issue, even though I followed Stork's BIOS settings exactly. I finally figured it out after tearing some of my hair out. Try enabling the Compatibility Support Module in the Boot tab in BIOS. I have no clue why, but that fixed it for me on two identical machines with...
@5T33Z0: FakePCIID was never used on these builds. I went ahead and made the recommended changes on this machine under 12.6.6, then updated OC to 0.9.2. Easy-peasy. All worked well; after an image backup, did the upgrade to 13.4 Ventura. Working great at this time. Thanks very much. OCAT...
Yes, thanks! I had found this page earlier, which is why I began looking into using OCAT to add the needed kext and .aml files, and edit config.plist. I supposed I could have used PepperTree, etc. (the "old" way) but OCAT looks like it's a much better tool. Hence the questions above (original...
Forgive the dumb question; I set up my new Hacks (upgraded from two older machines) back in September with OC 0.8.6/Monterey 12.1 (now on 12.6.6).
Upgrading one of them to Ventura b0rked my Internet (doesn't see my I-225V NIC). So, I'm now entering the brave new world of OCAT (there's...
I actually had forgot those were still in the kexts directory; I had used that method initially.
Anyway, I deleted them (and USBMap.kext as well, just to keep things clean with Hackintool) and added USBPorts.kext generated by Hackintool. This produced the attached scenario.
What's odd is...
Thanks, @UtterDisbelief.
Running MacOS Monterey 12.6.1, iMac20,2.
I did leave SSDT-RHUB.aml in place, as this is an Asus motherboard.
Clearing and refreshing the ports resulted in the same ones that I had previously identified (7) plus the one associated with the LED controller on the...
OK...tried to start USB mapping using Hackintool. Though it shows a lot of "active" ports, only seven of them actually changed when I plugged in a 2.0 or 3.0 flash drive (see attached). Only two of the six 3.0/3.1 ports on the back panel are actually active, as are most of the 2.0 and 3.0...
Thanks, @Stork. I downloaded the latest Hackintool, and with it, a ton of ports show up. So I will use it instead of USBMap to do the mapping per the instructions. Much appreciated!
I know that this is an old post, but I can only get 8 ports mapped with the original setup (with two others present in the "Discover Ports" option of USBMap, but they don't activate when I plug in a flash drive of either type).
When I add this modified USBInjectAll (Dren's) kext (I assume it is...
Started from scratch using OpenCore 0.8.6. Worked fine this time, with no ocvalidate errors. I *thought* I did everything the same as before, but I must not have. In any case, the machine is running Monterey 12.6 (triple-booting with WIndows 11 and Ubuntu Linux 22.04) without any glitches so...
OK, I tried it again, using ProperTree, of course. This time I deleted the "Patch" key completely, and now I get another error. Apparently is doesn't like the "Patch" key to be missing.
I compared the values in the sample config.plist file supplied with OC 0.8.5, and it had those same blank...
Hmmmm. That's interesting. I deleted them, saved the file, then opened it again, and they were gone.
I have another copy of my original file, will try it again when I get a chance.
Yes, ideally so, but it's an NVMe SSD which is installed under the slot that the graphics card is in. Can I remove it? Yeah, but it's a pain and makes it pretty tough to do any work on the machine! I did clone the drive, so if anything gets b0rked, it's easy enough to restore it...
Thanks for the reply.
Fixed original post and updated profile.
Added SSDT-EC-USBX-DESKTOP.aml (I went ahead and used their pre-built .aml files this time). Went through the rest of the "setting up config.plist" instructions again. Same result - I still only get "Windows" as an option...
Hi all -
I have two older Hacks, both 4th-gen i7s, maxed out at 10.15.7.
I needed a faster machine for tasks like photo and video editing, so have put together a new machine with a Z490 Asus ProArt Creator 10G (Comet Lake), i9-10850K, and a Radeon rx580 (very similar to Stork's build). Linux...
Hi all -
Not sure as to whether this is the right place to post this - mods, please feel free to relocate it if warranted.
Simple (I hope) question: I have two i7-4770K/Z97 machines, one with an NVidia 640 card, the other running with the onboard graphics.
I am planning to upgrade both to...
I have sound via HDMI to my external stereo receiver. However, the USB sound device (headphones/mic) still doesn't work. I use this for Zoom meetings, etc. It shows up on the list of devices but...no sound output. Any idea as to how to get it enabled?
Thanks!
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.