[SUCCESS] Gigabyte Designare Z390 (Thunderbolt 3) + i7-9700K + AMD RX 580

[Elias64Fr]

@Elias64Fr,

Welcome to the Designare Z390 owner's circle! Glad to have you on board!

So the hardware installation and software setup went smoothly?

This evening I'll send you the latest TbtOnPch files.

Regarding the screenshot you posted, did that happen after a hot-plug/hot-unplug followed by a hard boot?

I see that no TB3 devices are connected, but the Local Node and Bus still appeared?

Some issue with Power Supply .. and to found an old RX570 to avoid IGPU patching for quick installation ... and also native NVRAM enabling, quickly made with your precious guide but on IOReg, under AppleEFINVRAM. I had only three properties , now it work ! I still have to found how to enabling AppleVTD (like on my Asus board) by disabling DMAR drop table. I still have a kernel panic on boot.

OK for another version of SSDT ! I will test it for you and make some modifications if required.

This screen shot is done after a normal boot and without any devices connected !

Another informations :
- ThunderboltDROM is not required, but It will be usefull with some modifications on Port 7 in order to display some hidden informations on IOThunderboltPort@7, for customizing UUID (ThunderboltIP or something else) and VendorID/ProductID. New customized ThunderboltDROM might be accepted by macOS driver only after tuning CRC8 and CRC32 included data.
- ThunderboltConfig is not required, I don't know what the content means and what it configure !
- pathcr is finally not required

UPDATE:
Following System informations with UID randomly (?) created by macOS driver and different from 0x00ED00000...
Speed and status link are normal

Spoiler: Thunderbolt System Informations

 

[CaseySJ]

Some issue with Power Supply .. and to found an old RX570 to avoid IGPU patching for quick installation ... and also native NVRAM enabling, quickly made with your precious guide but on IOReg, under AppleEFINVRAM. I had only three properties , now it work ! I still have to found how to enabling AppleVTD (like on my Asus board) by disabling DMAR drop table. I still have a kernel panic on boot.

OK for another version of SSDT ! I will test it for you and make some modifications if required.

This screen shot is done after a normal boot and without any devices connected !

Another informations :
- ThunderboltDROM is not required, but It will be usefull with some modifications on Port 7 in order to display some hidden informations on IOThunderboltPort@7, for customizing UUID (ThunderboltIP or something else) and VendorID/ProductID. New customized ThunderboltDROM might be accepted by macOS driver only after tuning CRC8 and CRC32 included data.
- ThunderboltConfig is not required, I don't know what the content means and what it configure !
- pathcr is finally not required

UPDATE:
Following System informations with UID randomly (?) created by macOS driver and different from 0x00ED00000...
Speed and status link are normal

Spoiler: Thunderbolt System Informations

View attachment 451839

This is awesome! Will be home in about 30 minutes and will try out the changes you described.

 

[interobang]

Okay -- problem found:

• We are only supposed to change TEST_SWITCH at the top of the file on Line 85.
• But it seems you might have changed it everywhere throughout the file.

Please download EFIClone-v4.sh from the mini-guide once again, then remove the quarantine flag (xattr -d com.apple.quarantine EFIClone-v4.sh), change only line 85 to TEST_SWITCH="N", save the fie, then copy it to the CCC Scripts folder and secure that folder.

Perfect! it worked, thank you.

 

[CaseySJ]

Perfect! it worked, thank you.

Now you see why I wanted to set TEST_SWITCH to N by default!

 

[interobang]

Now you see why I wanted to set TEST_SWITCH to N by default!

I do! Maybe add to the guide: "change only line 85 to TEST_SWITCH="N"

 

[CaseySJ]

I do! Maybe add to the guide: "change only line 85 to TEST_SWITCH="N"

Good idea...done.

 

[CaseySJ]

Some issue with Power Supply .. and to found an old RX570 to avoid IGPU patching for quick installation ... and also native NVRAM enabling, quickly made with your precious guide but on IOReg, under AppleEFINVRAM. I had only three properties , now it work ! I still have to found how to enabling AppleVTD (like on my Asus board) by disabling DMAR drop table. I still have a kernel panic on boot.

OK for another version of SSDT ! I will test it for you and make some modifications if required.

This screen shot is done after a normal boot and without any devices connected !

Another informations :
- ThunderboltDROM is not required, but It will be usefull with some modifications on Port 7 in order to display some hidden informations on IOThunderboltPort@7, for customizing UUID (ThunderboltIP or something else) and VendorID/ProductID. New customized ThunderboltDROM might be accepted by macOS driver only after tuning CRC8 and CRC32 included data.
- ThunderboltConfig is not required, I don't know what the content means and what it configure !
- pathcr is finally not required

UPDATE:
Following System informations with UID randomly (?) created by macOS driver and different from 0x00ED00000...
Speed and status link are normal

Spoiler: Thunderbolt System Informations

View attachment 451839

I am able to duplicate your results!

• Cold boot
• No (a) ThunderboltDROM, (b) ThunderboltConfig, (c) pathcr
• With Belkin Thunderbolt 3 Dock Pro connected before boot
• The dock does not activate, but TNODE/TBUS chain appears immediately on cold boot
• And Link speed is not zero anymore, but 20 Gbps

Spoiler: ACPIDebug Logs

Timestamp                       (process)[PID]  
2020-02-26 18:53:57.716855-0800  localhost kernel[0]: (kernel) ACPIDebug: Version 0.1.4 starting on OS X Darwin 19.3.
2020-02-26 18:53:57.717023-0800  localhost kernel[0]: (kernel) ACPIDebug: { "RP05", 0xe00e4000, }
2020-02-26 18:53:57.717163-0800  localhost kernel[0]: (kernel) ACPIDebug: { "UPSB", 0xe0600000, }
2020-02-26 18:53:57.717283-0800  localhost kernel[0]: (kernel) ACPIDebug: { "DSB0", 0xe0700000, }
2020-02-26 18:53:57.717372-0800  localhost kernel[0]: (kernel) ACPIDebug: { "DSB1", 0xe0708000, }
2020-02-26 18:53:57.717458-0800  localhost kernel[0]: (kernel) ACPIDebug: { "DSB2", 0xe0710000, }
2020-02-26 18:53:57.717548-0800  localhost kernel[0]: (kernel) ACPIDebug: { "DSB4", 0xe0720000, }
2020-02-26 18:53:57.717634-0800  localhost kernel[0]: (kernel) ACPIDebug: { "NHI0", 0xe0800000, }
2020-02-26 18:53:57.717722-0800  localhost kernel[0]: (kernel) ACPIDebug: { "RSTR", 0x54039854, }
2020-02-26 18:53:57.717810-0800  localhost kernel[0]: (kernel) ACPIDebug: { "XHC2", 0xe0a00000, }
2020-02-26 18:53:57.717892-0800  localhost kernel[0]: (kernel) ACPIDebug: "RP05 Initialize"
2020-02-26 18:53:57.718082-0800  localhost kernel[0]: (kernel) ACPIDebug: "ICMBoot"
2020-02-26 18:53:57.718165-0800  localhost kernel[0]: (kernel) ACPIDebug: "ICUP - Our OSUP"
2020-02-26 18:53:57.718247-0800  localhost kernel[0]: (kernel) ACPIDebug: "ICUP - Cmd Ack'd"
2020-02-26 18:53:57.718329-0800  localhost kernel[0]: (kernel) ACPIDebug: "Tbt TWIN set to One"
2020-02-26 18:53:57.718518-0800  localhost kernel[0]: (kernel) ACPIDebug: "Tbt Force Power with FPG0"
2020-02-26 18:53:57.718601-0800  localhost kernel[0]: (kernel) ACPIDebug: "Upstream VID/DID okay"
2020-02-26 18:53:57.718684-0800  localhost kernel[0]: (kernel) ACPIDebug: { "ICME 1", 0xffffffff, }
2020-02-26 18:53:57.718767-0800  localhost kernel[0]: (kernel) ACPIDebug: "Configure NHI"
2020-02-26 18:53:57.718849-0800  localhost kernel[0]: (kernel) ACPIDebug: "Configure UPSB"
2020-02-26 18:53:57.718932-0800  localhost kernel[0]: (kernel) ACPIDebug: "Wait for link training"
2020-02-26 18:53:57.719014-0800  localhost kernel[0]: (kernel) ACPIDebug: "Configure DSB"
2020-02-26 18:53:57.719097-0800  localhost kernel[0]: (kernel) ACPIDebug: "Configure NHI Dp 0 done"
2020-02-26 18:53:57.719178-0800  localhost kernel[0]: (kernel) ACPIDebug: "Configure NHI Dp 3 done"
2020-02-26 18:53:57.719261-0800  localhost kernel[0]: (kernel) ACPIDebug: "Configure NHI Dp 4 done"
2020-02-26 18:53:57.719344-0800  localhost kernel[0]: (kernel) ACPIDebug: "Configure NHI Dp 5 done"
2020-02-26 18:53:57.719425-0800  localhost kernel[0]: (kernel) ACPIDebug: "Wait for down link"
2020-02-26 18:53:57.719509-0800  localhost kernel[0]: (kernel) ACPIDebug: { "NHI BAR", 0x54000000, }
2020-02-26 18:53:57.719592-0800  localhost kernel[0]: (kernel) ACPIDebug: "Configure NHI all done"
2020-02-26 18:53:57.719676-0800  localhost kernel[0]: (kernel) ACPIDebug: { "ICME 2", 0x800001a1, }
2020-02-26 18:53:57.719761-0800  localhost kernel[0]: (kernel) ACPIDebug: { "WTLT returns", 0x1, }
2020-02-26 18:53:57.719845-0800  localhost kernel[0]: (kernel) ACPIDebug: { "ICME 3", 0x800001a1, }
2020-02-26 18:53:57.719946-0800  localhost kernel[0]: (kernel) ACPIDebug: { "ICME 4", 0x800001a7, }
2020-02-26 18:53:57.720499-0800  localhost kernel[0]: (kernel) ACPIDebug: { "ISTA 1", 0x800003f0, }
2020-02-26 18:53:57.720620-0800  localhost kernel[0]: (kernel) ACPIDebug: { "ICME 5", 0x800001a7, }
2020-02-26 18:53:57.720742-0800  localhost kernel[0]: (kernel) ACPIDebug: { "ISTA 2", 0x800003f0, }
2020-02-26 18:53:57.720914-0800  localhost kernel[0]: (kernel) ACPIDebug: { "Configuration delay = ", "381 ms", }
2020-02-26 18:53:57.721035-0800  localhost kernel[0]: (kernel) ACPIDebug: "RP05 PCEU Enter"
2020-02-26 18:53:57.721555-0800  localhost kernel[0]: (kernel) ACPIDebug: "RP05 PCEU Exit"
2020-02-26 18:53:57.721724-0800  localhost kernel[0]: (kernel) ACPIDebug: "UPSB _PS0"
2020-02-26 18:53:57.721815-0800  localhost kernel[0]: (kernel) ACPIDebug: "UPSB PCED Enter"
2020-02-26 18:53:57.722005-0800  localhost kernel[0]: (kernel) ACPIDebug: { "UGIO Called by ", "UPSB.PCED", }
2020-02-26 18:53:57.722150-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - PCI wants on"
2020-02-26 18:53:57.722302-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - NHI wants on"
2020-02-26 18:53:57.722428-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - XHCI wants on"
2020-02-26 18:53:57.722578-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - TBT forced on"
2020-02-26 18:53:57.722707-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - USB forced on"
2020-02-26 18:53:57.722861-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - TBT GPIO should be on"
2020-02-26 18:53:57.722990-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - USB GPIO should be on"
2020-02-26 18:53:57.723122-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - Make sure TBT & USBC is on."
2020-02-26 18:53:57.723284-0800  localhost kernel[0]: (kernel) ACPIDebug: "TBT & USBC already on."
2020-02-26 18:53:57.723422-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO Exit"
2020-02-26 18:53:57.723532-0800  localhost kernel[0]: (kernel) ACPIDebug: "PCED UPSB- restored flag, THUNDERBOLT_PCI_LINK_MGMT_DEVICE.PRSR"
2020-02-26 18:53:57.723794-0800  localhost kernel[0]: (kernel) ACPIDebug: 0x0
2020-02-26 18:53:57.723974-0800  localhost kernel[0]: (kernel) ACPIDebug: "PCED UPSB- Wait for config space..."
2020-02-26 18:53:57.724155-0800  localhost kernel[0]: (kernel) ACPIDebug: "PCED UPSB- Read VID/DID okay"
2020-02-26 18:53:57.724334-0800  localhost kernel[0]: (kernel) ACPIDebug: { "Link width = ", 0x4, }
2020-02-26 18:53:57.724513-0800  localhost kernel[0]: (kernel) ACPIDebug: { "Link speed = ", 0x3, }
2020-02-26 18:53:57.724691-0800  localhost kernel[0]: (kernel) ACPIDebug: { "Link active = ", 0x1, }
2020-02-26 18:53:57.724868-0800  localhost kernel[0]: (kernel) ACPIDebug: { "Link train = ", 0x0, }
2020-02-26 18:53:57.725047-0800  localhost kernel[0]: (kernel) ACPIDebug: { "ASPM = ", 0x0, }
2020-02-26 18:53:57.725223-0800  localhost kernel[0]: (kernel) ACPIDebug: { "LWRT = ", 0x0, }
2020-02-26 18:53:57.725397-0800  localhost kernel[0]: (kernel) ACPIDebug: { "LWMR = ", 0xa, }
2020-02-26 18:53:57.725572-0800  localhost kernel[0]: (kernel) ACPIDebug: { "THUNDERBOLT_PCI_LINK_MGMT_DEVICE.PRSR = ", 0x0, }
2020-02-26 18:53:57.725749-0800  localhost kernel[0]: (kernel) ACPIDebug: { "TFLG = ", 0x0, }
2020-02-26 18:53:57.725927-0800  localhost kernel[0]: (kernel) ACPIDebug: { "Local4 (LinkIsUp) = ", 0x1, }
2020-02-26 18:53:57.726103-0800  localhost kernel[0]: (kernel) ACPIDebug: { "RetryForLinkWidth = ", 0x0, }
2020-02-26 18:53:57.726281-0800  localhost kernel[0]: (kernel) ACPIDebug: { "RetryForNoLink = ", 0x0, }
2020-02-26 18:53:57.726457-0800  localhost kernel[0]: (kernel) ACPIDebug: { "CanRetry = ", 0x0, }
2020-02-26 18:53:57.726632-0800  localhost kernel[0]: (kernel) ACPIDebug: "UPSB PCED Exit"
2020-02-26 18:53:57.726718-0800  localhost kernel[0]: (kernel) ACPIDebug: "CRMW Enter"
2020-02-26 18:53:57.726896-0800  localhost kernel[0]: (kernel) ACPIDebug: { "CRMW Read Value1", 0x34021, }
2020-02-26 18:53:57.727538-0800  localhost kernel[0]: (kernel) ACPIDebug: { "CRMW Write Value1", 0x4034021, }
2020-02-26 18:53:57.727863-0800  localhost kernel[0]: (kernel) ACPIDebug: { "CRMW Read Value2", 0x4034021, }
2020-02-26 18:53:57.728040-0800  localhost kernel[0]: (kernel) ACPIDebug: "CRMW Success"
2020-02-26 18:53:57.728215-0800  localhost kernel[0]: (kernel) ACPIDebug: "CRMW Exit"
2020-02-26 18:53:57.728389-0800  localhost kernel[0]: (kernel) ACPIDebug: "CRMW Enter"
2020-02-26 18:53:57.728475-0800  localhost kernel[0]: (kernel) ACPIDebug: { "CRMW Read Value1", 0x34121, }
2020-02-26 18:53:57.728653-0800  localhost kernel[0]: (kernel) ACPIDebug: { "CRMW Write Value1", 0x4034121, }
2020-02-26 18:53:57.728827-0800  localhost kernel[0]: (kernel) ACPIDebug: { "CRMW Read Value2", 0x4034121, }
2020-02-26 18:53:57.729155-0800  localhost kernel[0]: (kernel) ACPIDebug: "CRMW Success"
2020-02-26 18:53:57.729329-0800  localhost kernel[0]: (kernel) ACPIDebug: "CRMW Exit"
2020-02-26 18:53:57.729503-0800  localhost kernel[0]: (kernel) ACPIDebug: "ICMB Exit"
2020-02-26 18:53:57.755716-0800  localhost kernel[0]: (kernel) ACPIDebug: "RP05 _PS0"
2020-02-26 18:53:57.755916-0800  localhost kernel[0]: (kernel) ACPIDebug: "Called by macOS first time. No Op."
2020-02-26 18:53:57.760459-0800  localhost kernel[0]: (kernel) ACPIDebug: "UPSB _PS0"
2020-02-26 18:53:57.760847-0800  localhost kernel[0]: (kernel) ACPIDebug: "UPSB PCED Enter"
2020-02-26 18:53:55.203483-0800  localhost kernel[0]: (kernel) ACPIDebug: "PCEU DSB2"
2020-02-26 18:53:55.203600-0800  localhost kernel[0]: (kernel) ACPIDebug: "NHI0 PCED Enter"
2020-02-26 18:53:55.329363-0800  localhost kernel[0]: (kernel) ACPIDebug: "PCEU DSB2- Put upstream bridge back into D0 "
2020-02-26 18:53:55.329892-0800  localhost kernel[0]: (kernel) ACPIDebug: { "UGIO Called by ", "NHI0.PCED", }
2020-02-26 18:53:55.330428-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - PCI wants on"
2020-02-26 18:53:55.331017-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - NHI wants on"
2020-02-26 18:53:55.331546-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - XHCI wants on"
2020-02-26 18:53:55.332035-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - TBT forced on"
2020-02-26 18:53:55.332557-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - USB forced on"
2020-02-26 18:53:55.332690-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - TBT GPIO should be on"
2020-02-26 18:53:55.332858-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - USB GPIO should be on"
2020-02-26 18:53:55.332986-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - Make sure TBT & USBC is on."
2020-02-26 18:53:55.333098-0800  localhost kernel[0]: (kernel) ACPIDebug: "TBT & USBC already on."
2020-02-26 18:53:55.333207-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO Exit"
2020-02-26 18:53:55.333313-0800  localhost kernel[0]: (kernel) ACPIDebug: "_PS0 XHC2"
2020-02-26 18:53:55.458547-0800  localhost kernel[0]: (kernel) ACPIDebug: "PCED NHI0- restored flag, THUNDERBOLT_PCI_LINK_MGMT_DEVICE.PRSR"
2020-02-26 18:53:55.458700-0800  localhost kernel[0]: (kernel) ACPIDebug: "PCED XHC2 - enable GPIO"
2020-02-26 18:53:55.458851-0800  localhost kernel[0]: (kernel) ACPIDebug: 0x0
2020-02-26 18:53:55.459175-0800  localhost kernel[0]: (kernel) ACPIDebug: "PCED NHI0- Wait for config space..."
2020-02-26 18:53:55.459483-0800  localhost kernel[0]: (kernel) ACPIDebug: "PCED NHI0- Read VID/DID okay"
2020-02-26 18:53:55.459590-0800  localhost kernel[0]: (kernel) ACPIDebug: "NHI0 PCED Exit"
2020-02-26 18:53:55.584435-0800  localhost kernel[0]: (kernel) ACPIDebug: { "UGIO Called by ", "XHC2.PCED", }
2020-02-26 18:53:55.585326-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - PCI wants on"
2020-02-26 18:53:55.585870-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - NHI wants on"
2020-02-26 18:53:55.586358-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - XHCI wants on"
2020-02-26 18:53:55.586833-0800  localhost kernel[0]: (kernel) ACPIDebug: "CTBT Enter"
2020-02-26 18:53:55.587161-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - TBT forced on"
2020-02-26 18:53:55.587285-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - USB forced on"
2020-02-26 18:53:55.587400-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - TBT GPIO should be on"
2020-02-26 18:53:55.587511-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - USB GPIO should be on"
2020-02-26 18:53:55.587622-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - Make sure TBT & USBC is on."
2020-02-26 18:53:55.587734-0800  localhost kernel[0]: (kernel) ACPIDebug: "TBT & USBC already on."
2020-02-26 18:53:55.587851-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO Exit"
2020-02-26 18:53:55.712040-0800  localhost kernel[0]: (kernel) ACPIDebug: "CTBT Exit"
2020-02-26 18:53:55.712721-0800  localhost kernel[0]: (kernel) ACPIDebug: { "PCED XHC2- restored flag, THUNDERBOLT_PCI_LINK_MGMT_DEVICE.PRSR", 0x0, }
2020-02-26 18:53:55.712865-0800  localhost kernel[0]: (kernel) ACPIDebug: "PCED XHC2- Wait for config space..."
2020-02-26 18:53:55.713445-0800  localhost kernel[0]: (kernel) ACPIDebug: "PCED XHC2- Read VID/DID okay"
2020-02-26 18:53:55.713555-0800  localhost kernel[0]: (kernel) ACPIDebug: "XHC2 PCED Exit"
2020-02-26 18:53:55.845000-0800  localhost kernel[0]: (kernel) ACPIDebug: { "RTPC XHC2 called with arg: ", 0x1, }
2020-02-26 18:53:55.845979-0800  localhost kernel[0]: (kernel) ACPIDebug: { "XHC2 MODU - return = ", 0x1, }
2020-02-26 18:53:55.846129-0800  localhost kernel[0]: (kernel) ACPIDebug: { "XHC2 MODU - return = ", 0x1, }
2020-02-26 18:53:57.016745-0800  localhost kernel[0]: (kernel) ACPIDebug: "MUST NHI0"
2020-02-26 18:53:57.016926-0800  localhost kernel[0]: (kernel) ACPIDebug: { "MUST UPSB with arg", 0x0, }
2020-02-26 18:53:57.017041-0800  localhost kernel[0]: (kernel) ACPIDebug: "UPSB UMPE"
2020-02-26 18:53:57.017889-0800  localhost kernel[0]: (kernel) ACPIDebug: "XHC MODU"
2020-02-26 18:53:57.018249-0800  localhost kernel[0]: (kernel) ACPIDebug: { "XHC2 MODU - return = ", 0x0, }
2020-02-26 18:53:57.018794-0800  localhost kernel[0]: (kernel) ACPIDebug: { "XHC2 MODU - return = ", 0x0, }
2020-02-26 18:53:57.019147-0800  localhost kernel[0]: (kernel) ACPIDebug: { "XHC2 MODU - return = ", 0x0, }
2020-02-26 18:53:57.019738-0800  localhost kernel[0]: (kernel) ACPIDebug: "XHC MODU"
2020-02-26 18:53:57.019934-0800  localhost kernel[0]: (kernel) ACPIDebug: { "XHC2 MODU - return = ", 0x0, }
2020-02-26 18:53:57.020053-0800  localhost kernel[0]: (kernel) ACPIDebug: "XHC MODU"
2020-02-26 18:53:57.020169-0800  localhost kernel[0]: (kernel) ACPIDebug: { "XHC2 MODU - return = ", 0x0, }
2020-02-26 18:53:57.020285-0800  localhost kernel[0]: (kernel) ACPIDebug: { "RTPC XHC2 called with arg: ", 0x0, }
2020-02-26 18:53:57.020749-0800  localhost kernel[0]: (kernel) ACPIDebug: "_PS3 XHC2, Nothing to do!"
2020-02-26 18:53:57.176542-0800  localhost kernel[0]: (kernel) ACPIDebug: "_PS3 DSB2"
2020-02-26 18:53:57.303175-0800  localhost kernel[0]: (kernel) ACPIDebug: "PCDA DSB2"
2020-02-26 18:53:57.429315-0800  localhost kernel[0]: (kernel) ACPIDebug: "POFF DSB2"
2020-02-26 18:53:57.560144-0800  localhost kernel[0]: (kernel) ACPIDebug: "PCDA DSB2- Put upstream bridge into D3"
2020-02-26 18:53:57.560272-0800  localhost kernel[0]: (kernel) ACPIDebug: "PCDA DSB2- Set link disable on upstream bridge"
2020-02-26 18:53:57.560398-0800  localhost kernel[0]: (kernel) ACPIDebug: "PCDA DSB2- Wait for link to drop..."
2020-02-26 18:53:57.560522-0800  localhost kernel[0]: (kernel) ACPIDebug: "PCDA DSB2- XHC2 not present"
2020-02-26 18:53:57.560647-0800  localhost kernel[0]: (kernel) ACPIDebug: "PCDA DSB2 - disable GPIO"
2020-02-26 18:53:57.560773-0800  localhost kernel[0]: (kernel) ACPIDebug: { "UGIO Called by ", "DSB2.PCDA", }
2020-02-26 18:53:57.560897-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - PCI wants on"
2020-02-26 18:53:57.561021-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - NHI wants on"
2020-02-26 18:53:57.561144-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - XHCI wants off"
2020-02-26 18:53:57.561282-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - TBT forced on"
2020-02-26 18:53:57.561396-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - USB allows off"
2020-02-26 18:53:57.561508-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - TBT GPIO should be on"
2020-02-26 18:53:57.561621-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - USB GPIO should be off"
2020-02-26 18:53:57.561734-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - Make sure TBT & USBC is on."
2020-02-26 18:53:57.561846-0800  localhost kernel[0]: (kernel) ACPIDebug: "TBT & USBC already on."
2020-02-26 18:53:57.561959-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO Exit"
2020-02-26 18:53:57.686483-0800  localhost kernel[0]: (kernel) ACPIDebug: "DSB2 PCDA Exit"
2020-02-26 18:54:31.358737-0800  localhost kernel[0]: (kernel) ACPIDebug: "_E17 Enter"
2020-02-26 18:54:31.358863-0800  localhost kernel[0]: (kernel) ACPIDebug: "UPSB AMPE"
2020-02-26 18:54:31.358985-0800  localhost kernel[0]: (kernel) ACPIDebug: "UPSB UMPE"
2020-02-26 18:54:31.359955-0800  localhost kernel[0]: (kernel) ACPIDebug: { "XHC2 MODU - return = ", 0x0, }
2020-02-26 18:54:31.360375-0800  localhost kernel[0]: (kernel) ACPIDebug: "XHC MODU"
2020-02-26 18:54:31.360969-0800  localhost kernel[0]: (kernel) ACPIDebug: { "XHC2 MODU - return = ", 0x0, }
2020-02-26 18:54:31.361350-0800  localhost kernel[0]: (kernel) ACPIDebug: { "XHC2 MODU - return = ", 0x0, }
2020-02-26 18:54:31.361767-0800  localhost kernel[0]: (kernel) ACPIDebug: "XHC MODU"
2020-02-26 18:54:31.361904-0800  localhost kernel[0]: (kernel) ACPIDebug: { "XHC2 MODU - return = ", 0x0, }
2020-02-26 18:54:31.362035-0800  localhost kernel[0]: (kernel) ACPIDebug: "XHC MODU"
2020-02-26 18:54:31.362167-0800  localhost kernel[0]: (kernel) ACPIDebug: { "XHC2 MODU - return = ", 0x0, }
2020-02-26 18:54:31.376159-0800  localhost kernel[0]: (kernel) ACPIDebug: "_E17 Exit"
2020-02-26 18:54:33.231007-0800  localhost kernel[0]: (kernel) ACPIDebug: "MUST NHI0"
2020-02-26 18:54:33.231173-0800  localhost kernel[0]: (kernel) ACPIDebug: { "MUST UPSB with arg", 0x0, }
2020-02-26 18:54:42.443360-0800  localhost kernel[0]: (kernel) ACPIDebug: "MUST NHI0"
2020-02-26 18:54:42.443560-0800  localhost kernel[0]: (kernel) ACPIDebug: { "MUST UPSB with arg", 0x0, }
2020-02-26 18:55:00.522326-0800  localhost kernel[0]: (kernel) ACPIDebug: { "RTPC NHI0 called with arg: ", 0x0, }
2020-02-26 18:55:00.523032-0800  localhost kernel[0]: (kernel) ACPIDebug: "_PS3 NHI0, Nothing to do!"
2020-02-26 18:55:00.649834-0800  localhost kernel[0]: (kernel) ACPIDebug: "_PS3 DSB0"
2020-02-26 18:55:00.776363-0800  localhost kernel[0]: (kernel) ACPIDebug: "DSB0 PCDA"
2020-02-26 18:55:00.902839-0800  localhost kernel[0]: (kernel) ACPIDebug: "POFF DSB0"
2020-02-26 18:55:01.030274-0800  localhost kernel[0]: (kernel) ACPIDebug: "PCDA DSB0- Put upstream bridge into D3"
2020-02-26 18:55:01.030516-0800  localhost kernel[0]: (kernel) ACPIDebug: "PCDA DSB0- Set link disable on upstream bridge"
2020-02-26 18:55:01.030758-0800  localhost kernel[0]: (kernel) ACPIDebug: "PCDA DSB0- Wait for link to drop..."
2020-02-26 18:55:02.043069-0800  localhost kernel[0]: (kernel) ACPIDebug: "PCDA DSB0- disable GPIO"
2020-02-26 18:55:02.043212-0800  localhost kernel[0]: (kernel) ACPIDebug: { "UGIO Called by ", "DSB0.PCDA", }
2020-02-26 18:55:02.043351-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - PCI wants on"
2020-02-26 18:55:02.043493-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - NHI wants off"
2020-02-26 18:55:02.043630-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - XHCI wants off"
2020-02-26 18:55:02.043766-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - TBT allows off"
2020-02-26 18:55:02.043902-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - USB allows off"
2020-02-26 18:55:02.044039-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - TBT GPIO should be on"
2020-02-26 18:55:02.044175-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - USB GPIO should be on"
2020-02-26 18:55:02.044312-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - Make sure TBT & USBC is on."
2020-02-26 18:55:02.044448-0800  localhost kernel[0]: (kernel) ACPIDebug: "TBT & USBC already on."
2020-02-26 18:55:02.044585-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO Exit"
2020-02-26 18:55:02.169142-0800  localhost kernel[0]: (kernel) ACPIDebug: "UPSB _PS3 - No Op"
2020-02-26 18:55:02.295568-0800  localhost kernel[0]: (kernel) ACPIDebug: "RP05 _PS3"
2020-02-26 18:55:02.421085-0800  localhost kernel[0]: (kernel) ACPIDebug: "POFF RP05"
2020-02-26 18:55:02.421219-0800  localhost kernel[0]: (kernel) ACPIDebug: "CTBT Enter"
2020-02-26 18:55:02.547859-0800  localhost kernel[0]: (kernel) ACPIDebug: "CTBT Exit"
2020-02-26 18:55:02.547990-0800  localhost kernel[0]: (kernel) ACPIDebug: "RP05 PCDA Enter"
2020-02-26 18:55:02.678025-0800  localhost kernel[0]: (kernel) ACPIDebug: "POFF RP05"
2020-02-26 18:55:02.678169-0800  localhost kernel[0]: (kernel) ACPIDebug: "PCDA RP05- Put upstream bridge into D3"
2020-02-26 18:55:02.678311-0800  localhost kernel[0]: (kernel) ACPIDebug: "PCDA RP05- Set link disable on upstream bridge"
2020-02-26 18:55:02.678464-0800  localhost kernel[0]: (kernel) ACPIDebug: "PCDA RP05- Wait for link to drop..."
2020-02-26 18:55:02.678594-0800  localhost kernel[0]: (kernel) ACPIDebug: "PCDA RP05- No link activity"
2020-02-26 18:55:02.678722-0800  localhost kernel[0]: (kernel) ACPIDebug: "PCDA RP05- disable GPIO"
2020-02-26 18:55:02.678854-0800  localhost kernel[0]: (kernel) ACPIDebug: { "UGIO Called by ", "RP05.PCDA", }
2020-02-26 18:55:02.678982-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - PCI wants off"
2020-02-26 18:55:02.679111-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - NHI wants off"
2020-02-26 18:55:02.679240-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - XHCI wants off"
2020-02-26 18:55:02.679368-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - TBT allows off"
2020-02-26 18:55:02.679497-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - USB allows off"
2020-02-26 18:55:02.679626-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - TBT GPIO should be off"
2020-02-26 18:55:02.679754-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - USB GPIO should be off"
2020-02-26 18:55:02.679882-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - Make sure TBT & USBC is off."
2020-02-26 18:55:02.680011-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - Make sure TBT & USBC is off"
2020-02-26 18:55:02.680138-0800  localhost kernel[0]: (kernel) ACPIDebug: "CTBT Enter"
2020-02-26 18:55:02.805905-0800  localhost kernel[0]: (kernel) ACPIDebug: "CTBT Exit"
2020-02-26 18:55:02.806113-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO - CP_ACK_POWERDOWN_OVERRIDE not configured, cannot turn off TBT GPIO"
2020-02-26 18:55:02.806292-0800  localhost kernel[0]: (kernel) ACPIDebug: "UGIO Exit"
2020-02-26 18:55:02.932519-0800  localhost kernel[0]: (kernel) ACPIDebug: "RP05 PCDA Exit"

 

[CaseySJ]

@Elias64Fr,

Okay, after connecting the Apple Thunderbolt-to-Gigabit Ethernet via Apple TB3-to-TB2 adapter, look what we get!!


Above results obtained with:

• Thunderbolt Boot Support disabled
• GPIO3 Force Power disabled

 

[jiny505]

Hi @CaseySJ
I installed Catalina, but Graphics don't work correctly.

<< Solved >> - RX 580 Graphics Problem

I installed Catalina, but Graphics don't work correctly. 1. In Unibeast Graphics Configuration Step, I didn't select ATI. Did I have to select ATI for RX 580? 2. This is my CLOVER and Library/Extensions(I copied AMD9500Controller.kext and WhateverGreen.kext) How can I solve this?

www.tonymacx86.com

Any advice?

 

[nels1]

Hello @nels1,

It should be relatively straightforward to update the acidanthera kexts (VirtualSMC, Lilu, WhateverGreen, AppleALC). Because you're running Mojave, copy the new versions to both:

• /Library/Extensions
• CLOVER/kexts/Other

And run Kext Utility to rebuild the kernel cache.

However, because you've upgraded Clover from 4xxx to 5xxx, please check that the older CLOVER/drivers64UEFI folder has been deleted, and all needed EFI drivers are present in the new CLOVER/drivers/UEFI folder. If in doubt, grab a screenshot of the following:

• /Library/Extensions
• CLOVER/kexts/Other
• CLOVER/drivers/UEFI
• CLOVER

Thank you for your answer, I still have the CLOVER/drivers64UEFI present, so I will delete it, but before, here's a screenshot of what I've got now. Do I need to move HFSPlus-64.efi & VirtualSmc.efi to CLOVER/drivers/UEFI ?
And what about this nvram.plist ! I don't even know what is it and if I need it.
Thanks