[SUCCESS] Ongoing Status of Designare Z390 with i7-9700K

[CaseySJ]

Rx580 connected hdmi out - the message and screen lost signal ... 8 pins disconnected hdmi gpu out same message and screen lost signal.. i used mojave 14.1.0 with unibeast

Your first post indicates you are still in the process of installing Mojave. When you start the computer, do you press F12 and choose the USB disk? Then select:

• Stage 1 Installation: "Boot Install macOS Mojave from Install macOS Mojave"

• Stage 2 Installation: "Boot Install macOS Mojave from Mojave"

I would suggest 2 things:

1. Search this forum for "gIOScreenLockState". If no helpful solution, then try #2 below.
2. Start again from Stage 1. Follow METHOD 1 of my Build Guide. But the guide is for Designare board so be careful if you have a different board!

 

[logritm]

Your first post indicates you are still in the process of installing Mojave. When you start the computer, do you press F12 and choose the USB disk? Then select:

• Stage 1 Installation: "Boot Install macOS Mojave from Install macOS Mojave"

• Stage 2 Installation: "Boot Install macOS Mojave from Mojave"

I would suggest 2 things:

1. Search this forum for "gIOScreenLockState". If no helpful solution, then try #2 below.
2. Start again from Stage 1. Follow METHOD 1 of my Build Guide. But the guide is for Designare board so be careful if you have a different board!

I have a MB z390 designare rev 1.0 .. I am in the first part of the installation ... i press f12 to boot and i choose on clover boot install macos mojave.. i was trying to find someother posts with gIOscreenlockstate ..someone said to use on clover config boot -disablefxfirmware but it didnt help and i tried nv_disable=1 ... still nothing

 

[CaseySJ]

I have a MB z390 designare rev 1.0 .. I am in the first part of the installation ... i press f12 to boot and i choose on clover boot install macos mojave.. i was trying to find someother posts with gIOscreenlockstate ..someone said to use on clover config boot -disablefxfirmware but it didnt help and i tried nv_disable=1 ... still nothing

Okay, because you have the same motherboard, I should be able to help.

1. The problem might be in the EFI folder on your USB disk. Please zip and upload that folder.
2. You said you could not find a setting for XMP Profile 1. When you enter BIOS Setup, choose the "Classic" mode (not Simple mode) and the top left item will be: M.I.T. Inside this page, the 2nd item will change Memory settings. You can select XMP Profile 1.

Also please have a look at the Build Guide.

 

[logritm]

Okay, because you have the same motherboard, I should be able to help.

1. The problem might be in the EFI folder on your USB disk. Please zip and upload that folder.
2. You said you could not find a setting for XMP Profile 1. When you enter BIOS Setup, choose the "Classic" mode (not Simple mode) and the top left item will be: M.I.T. Inside this page, the 2nd item will change Memory settings. You can select XMP Profile 1.

Also please have a look at the Build Guide.

this is my efi. I read somewhere that M.I.T is only showed for the latest cpu .. i have 8700k .. if i choose classic mode i still cant see any M.I.T

 

[NoiseCoalition]

It looks like a problem with the kernel cache. Let's try this first:

• Boot to Clover, but choose the Recovery volume.
• When Recovery starts, choose Terminal from Tools menu and type:

cd /
kextcache -i /Volumes/Mojave

• This will rebuild the kernel cache. When complete, quit Terminal and Reboot from the Apple menu.
• Then try booting your Mojave volume and see if the problem persists.

I tried rebuilding the kernel cache then re-enabling internal graphics. Computer still hangs but the last line now says "Start UncompressKernelCache" instead of "Start ReadKernelCache". Strange.

 

[logritm]

Okay, because you have the same motherboard, I should be able to help.

1. The problem might be in the EFI folder on your USB disk. Please zip and upload that folder.
2. You said you could not find a setting for XMP Profile 1. When you enter BIOS Setup, choose the "Classic" mode (not Simple mode) and the top left item will be: M.I.T. Inside this page, the 2nd item will change Memory settings. You can select XMP Profile 1.

Also please have a look at the Build Guide.

I tried to start again from scratch .. formatted 32gb pendrive ... unibeat using this time mojave 10.14.2 ( before i used 10.14.1) ... and i still have the same error... i need help please

@Markzers i saw that you are using z390 designare with 8700k ... can you please post your EFI ?

 

[CaseySJ]

I’m currently in transit between the west coast and the east coast of the US. Will be able to respond a bit later in the day.

 

[logritm]

I’m currently in transit between the west coast and the east coast of the US. Will be able to respond a bit later in the day.

I want to thank you for your great work ... i fixed my problem .... at beginning everytime i had this gIOscreenlockstate error i turned off the computer... i resolved connecting and disconnecting the hdmi cable and the screen showed the mojave installation... so strange... after that i had other noises screen error... so i changed hdmi cable... i think that rx580 not support new hdmi cables with ethernet...

Now my hackintosh look perfect thank you

 

[CaseySJ]

Awesome and congratulations!

What kind of HDMI cable gave you the problem? Do you have an Amazon link for the (bad) cable? I will mention this in the build guide so other people can avoid this problem.

 

[logritm]

Awesome and congratulations!

What kind of HDMI cable gave you the problem? Do you have an Amazon link for the (bad) cable? I will mention this in the build guide so other people can avoid this problem.

it was my first hackintosh and I feel so happy that with your Guide I was able to run it .... the only little problem that I have is when I boot macOS the screen stop and I have to plug and unplug the hdmi cable ( another old cable that I have ) for one time....but after that it work without any problem for now....it look like rx580 hdmi not wake up on boot ... someone have any tips for this ??

the cable that give me a lot of problem is this one ( noise, black screen, plug & unplug ) ...dont buy it
https://www.amazon.com/dp/B003VX42MA/?tag=tonymacx86com-20

the Geekbench is 28283 ...not great as your because I have 8700k & 32 gb 2666hz ...and I still have macos on ssd ... I will migrate on nvme 1tb tomorrow .... I have to buy a tb2 /tb3 adapter for my uad octo satellite ... and your bt /wifi adapter ...