Contribute
Register

[SOLVED] Unable to boot into Clover from USB (Fujitsu AH512)

Status
Not open for further replies.
DSDT removed, reverted back to your HD300 7series 1366x768 config

Still same symptoms
 

Attachments

  • CLOVER.zip
    1.4 MB · Views: 52
If you can't boot, a bare minimum is:
- Boot verbose, attach photo
- Attach EFI/Clover folder as ZIP (press F2 then F4 at main Clover screen just before collecting). Please eliminate 'themes' directory. Provide only EFI/Clover, not the entire EFI folder.
Click to expand...

I'm not sure what else is required, I've attached the Clover Folder.
I can take a photo of a black screen but I can't see how that helps anything.
 
Ji-Ji said:
DSDT removed, reverted back to your HD300 7series 1366x768 config

Still same symptoms
Click to expand...
Ji-Ji said:
I'm not sure what else is required, I've attached the Clover Folder.
I can take a photo of a black screen but I can't see how that helps anything.
Click to expand...

You never mentioned anything regarding black screen.

As per guide, you should try booting with an invalid FakeID (0x12345678).
You may need to inject EDID.
 
RehabMan said:
You never mentioned anything regarding black screen.

As per guide, you should try booting with an invalid FakeID (0x12345678).
You may need to inject EDID.
Click to expand...

Apologies Rehabman, it was in Post 17.
With regards to EDID injection for an installer, are there any suitable guides or resources you could guide me to? I'm struggling to locate a guide that could help me. I've extracted the EDID information from booting Windows on the laptop (popped the old hard drive in to run Windows again.)
 
Ji-Ji said:
Apologies Rehabman, it was in Post 17.
With regards to EDID injection for an installer, are there any suitable guides or resources you could guide me to? I'm struggling to locate a guide that could help me. I've extracted the EDID information from booting Windows on the laptop (popped the old hard drive in to run Windows again.)
Click to expand...

No need to inject EDID for the installer (although it is easily done in config.plist/Graphics/EDID).
You can use an invalid FakeID, and work on graphics (EDID inject, backlight control, etc) in post-install.
 
RehabMan said:
No need to inject EDID for the installer (although it is easily done in config.plist/Graphics/EDID).
You can use an invalid FakeID, and work on graphics (EDID inject, backlight control, etc) in post-install.
Click to expand...

I have tried FakeID previously it's the same outcome sadly.

I'm thinking it may be more than just a Graphics issue, as the whole system stop at this point, the laptop falls silent.
 
Ji-Ji said:
I have tried FakeID previously it's the same outcome sadly.
Click to expand...

You will need to attach PR files that represent this attempt.
 

Attachments

  • CLOVER.zip
    1.4 MB · Views: 44
Ji-Ji said:
As requested, still black screen, system hang. No verbose
Click to expand...

This misc/preboot.log shows no attempt to boot.
No verbose boot photo attached.

You must after booting into Clover:
- press F2
- press F4
- press spacebar (with macoOS boot target selected
- tick verbose boot
- attempt to boot

Attach resulting EFI/Clover and image screen that results.

Note: If you suspect a graphics issue, it is best to set config.plist/Devices/FakeID/IntelGFX=0x123435678 such that you don't forget to change it in Clover options.

Also, your profile is missing important details. Please fix as per FAQ:
http://www.tonymacx86.com/el-capita...faq-read-first-laptop-frequent-questions.html

Make sure you're using a USB2 flash drive in a USB2 port. As per guide, you may need USBInjectAll.kext and/or FakePCIID.kext+FakePCIID_XHCIMux.kext.
 
Status
Not open for further replies.
Copyright © 2010 - 2024 tonymacx86 LLC
Back
Top