MSI X99A SLI PLUS i7 6800k & ASUS 1080=HIGH SIERRA 13.2

[yannh1992]

I use "config.plist"

i tried something in "config2.plist"

 

[josh-x00]

I use "config.plist"

i tried something in "config2.plist"

ok, thank you very much, I succeeded in installing with config.plist. XCPM works too.

now, I configured it as Broadwell, everything goes, but XCMP is broken.

here you are my EFI for iMAC PRO 10.13.5 with Broadwell parameters.

 

[josh-x00]

I forgot to say:
if I enable EIST and add PMDrvr.kext, there is NO native power management: sysctl machdep.xcpm.mode shows 0 and CPU manages its load correctly (1.2 ghz up to 4.2, my OC frequency).

with EIST enabled, during boot, I see that some P states are sent, but not recognised... that's where I'm stuck, with Broadwell configuration.

any ideas?

 

[Chachu]

Here it is, have fun trying

Just saw it, thank u very much, I will check it out and post results asap

 

[josh-x00]

this is my EFI folder for Mac Pro 10.13.4 supplemental update.

SMBIOS: Mac Pro 6,1; fakecpuid: 0x040674.

OC (up to 4.2 ghz) and XCPM work fine.

if I adopt the same fakecpuid for iMAC PRO, as I said before, native PM breaks.

 

[josh-x00]

Guys, take a look at this EFI. it seems it works with iMAC PRO 10.13.6 w/ OC and XCPM (Broadwell E fakecpuid).

Just one note: when I perform any system update, I have to change AptioMemoryFix.efi with OsxAptioFix2Drv-free2000.efi and "play" with 4G decoding in bios (enable / disable it, depending on the system stuck on ++++++++++++++ or not). I switch back to aptio when the update is completed.

these are my OC settings, under water cooled custom loop:
vccin: 1.9
core: 1.25
ring: 1.15
IO: 1
SA: 1
ring: auto
multiplier: 42
pch: 1.05 / 1.5
cpu core/ring: adaptive
ddr: 1.35
dram: 1-13-14-14-35
dram freq: 2666

and also:
4G encoding: enable
EIST: disable

geekbench: 5107 / 26774
cinebench: 1310

 

[josh-x00]

guys, this is my last EFI.
thank you all!

 

[cengear1]

guys, this is my last EFI.
thank you all!

Thanks for your EFI folder!My 6900K works fine now and the system can correctly recognize my gtx 1060 graphic card now,which was recognized as Vega 64 before(but it works fine)...

I still getting a problem about it takes very long time to boot the macOS after select the partition in clover.Sometime very soon.

Hope you can give me some help.

Thanks a lot again!

 

[BreBo]

@cengear1, please update your profile (personal details) with your Motherboard, CPU and iGPU or Graphics Card(s).

Profiles are mandatory so that others can assist you.

 

[josh-x00]

Thanks for your EFI folder!My 6900K works fine now and the system can correctly recognize my gtx 1060 graphic card now,which was recognized as Vega 64 before(but it works fine)...

I still getting a problem about it takes very long time to boot the macOS after select the partition in clover.Sometime very soon.

Hope you can give me some help.

Thanks a lot again!

Which is your configuration? Please, update your profile.