[Guide] HP Envy Haswell series J/K using Clover UEFI

[feloccio]

I run the power management scripts again (probably forgot it the last time)
Should i disable the hibernation mode? Because sleep (blinking LED) works fine. Will it still work afterwards? I skipped it for now.

Everything works vey well! Now i can focus on my Video Project.
Another (probably stupid) Question. Is it possible to enable the nvidia 750m? Would be very useful in Final Cut Pro, at least for CUDA.

So far i see no problems, but i will post the files anyway for feedback:

kextstat|grep -y acpiplat   13    2 0xffffff7f82223000 0x65000    0x65000    com.apple.driver.AppleACPIPlatform (3.1) <12 11 7 6 5 4 3 1>
kextstat|grep -y

View attachment CLOVER.zip
View attachment RehabMan.zip
View attachment Felixs MacBook Pro.ioreg

 

[RehabMan]

I did everything in post 1. Everything works perfect besides audio. No devices found, only hdmi.

Read post #1, "Problem reporting".

 

[RehabMan]

I run the power management scripts again (probably forgot it the last time)

Still missing. Note from Clover bootlog, no SSDT.aml present:

7:740  0:000  Inserting table[1]:SSDT-2.aml from EFI\CLOVER\ACPI\patched ... Success
7:742  0:001  Inserting table[2]:SSDT-3.aml from EFI\CLOVER\ACPI\patched ... Success
7:744  0:001  Inserting table[3]:SSDT-4.aml from EFI\CLOVER\ACPI\patched ... Success
7:746  0:001  Inserting table[4]:SSDT-5.aml from EFI\CLOVER\ACPI\patched ... Success

Note that the file is present in the Clover folder you provided. So perhaps you just uploaded the wrong ioreg.

Should i disable the hibernation mode? Because sleep (blinking LED) works fine. Will it still work afterwards? I skipped it for now.

Hibernation (suspend to disk) is not the same as sleep (suspend to RAM).

Hibernation is not supported and should be disabled.

Another (probably stupid) Question. Is it possible to enable the nvidia 750m? Would be very useful in Final Cut Pro, at least for CUDA.

No.

 

[1mperial]

Read post #1, "Problem reporting".

Already tried, no effect..

 

[RehabMan]

Already tried, no effect..

The "effect" would be you providing the files (upload as attachment) that are requested...

Perhaps you should actually read that section and provide the files... just as @feloccio did in post #91.

 

[1mperial]

The "effect" would be you providing the files (upload as attachment) that are requested...

Perhaps you should actually read that section and provide the files... just as @feloccio did in post #91.

Here is clover folder

 

[RehabMan]

Here is clover folder

Please provide all files requested in post #1, "Problem reporting".

 

[1mperial]

Please provide all files requested in post #1, "Problem reporting".

Sorry for that. Here are all files

 

[RehabMan]

Sorry for that. Here are all files

Make sure AppleHDA_IDT76e0_Envy.kext is installed (install_downloads.sh does this).

Complete the following procedure:
- repair permissions (Disk Utility)
- reboot without caches
- quickly, rebuild cache (Kext Utility or DPCIManager)
- reboot two times (normally)

 

[1mperial]

Make sure AppleHDA_IDT76e0_Envy.kext is installed (install_downloads.sh does this).

Complete the following procedure:
- repair permissions (Disk Utility)
- reboot without caches
- quickly, rebuild cache (Kext Utility or DPCIManager)
- reboot two times (normally)

It is here. Ok, i'll try to do it quickly)