- Joined
- Feb 13, 2011
- Messages
- 2
- Motherboard
- GA-H67M-D2-B3
- CPU
- Intel Core i3
- Graphics
- Intel HD3000
- Mac
- Classic Mac
- Mobile Phone
So, Lion 10.7.2 works on my GA-H67M-D2-B3 with: Ethernet, Audio, USB. I have no separate graphics card so I'm attempting to using the onboard Intel HD3000.
The route to build was:
1. Setup Bios with ACPI and HPET mode to 64bit
2. using iBoot to install Retail version of Snow Leopard (SL) 10.6.3 (Safe Mode boot)
3. upgrade SL to 10.6.7 using Combo Upgrade (GraphicsEnabler=No)
4. Multibeast for SL to get system using the "DSDT-GA-H67M-D2-B3-1.1-F4.aml" DSDR and the Network drivers work using Lnx2Mac's.
5. run UpgradeHelper
6. upgrade to SL version 10.6.8 (GraphicsEnabler=No)
7. Once here, it was a Simple Unibeast method to get to a Retail Version of Lion 10.7.2 (GraphicsEnabler=No)
8. using the options post install of Multibeast with the options:
...UserDSDT (DSDT-GA-H67M-D2-B3-1.1-F4.aml)
...Drivers & Bootloaders -> Audio
......ALC8xxDHA
......AppleHDA Rollback
......Non-DSDT HDAEnabler -> ALC889
...System Definitions -> Mac Mini
...OSx86 Software
......Kext Utility
......ShowAllFiles
System all works but without successfully booting without GraphicsEnabler=No!!!
Just got lion working but have to boot with GraphicsEnabler=no + flash doesnt work and launchpad flickers
My monitor connection is via VGA as my motherboard does not a direct HDMI output, I have ordered a DVI to HDMI connector so that I can test via DVI to my TV, but not tested this yet.
When I boot with 'GraphicsEnabler=Yes' and verbose mode. I am getting the error:
Sound assertion ""ERROR: EFI ROM did not publish 'hda-gfx' associative property!\n"" failed in AppleHDACodecGeneric at line 331.
I've been looking though lots of similar posts at getting the HD3000 working, but I've not managed to succeed yet. Any help available would be most welcome.
I'd also like to say thanks to all that have contributed to make this work - it very impressive the work and talent that have made this possible.
The route to build was:
1. Setup Bios with ACPI and HPET mode to 64bit
2. using iBoot to install Retail version of Snow Leopard (SL) 10.6.3 (Safe Mode boot)
3. upgrade SL to 10.6.7 using Combo Upgrade (GraphicsEnabler=No)
4. Multibeast for SL to get system using the "DSDT-GA-H67M-D2-B3-1.1-F4.aml" DSDR and the Network drivers work using Lnx2Mac's.
5. run UpgradeHelper
6. upgrade to SL version 10.6.8 (GraphicsEnabler=No)
7. Once here, it was a Simple Unibeast method to get to a Retail Version of Lion 10.7.2 (GraphicsEnabler=No)
8. using the options post install of Multibeast with the options:
...UserDSDT (DSDT-GA-H67M-D2-B3-1.1-F4.aml)
...Drivers & Bootloaders -> Audio
......ALC8xxDHA
......AppleHDA Rollback
......Non-DSDT HDAEnabler -> ALC889
...System Definitions -> Mac Mini
...OSx86 Software
......Kext Utility
......ShowAllFiles
System all works but without successfully booting without GraphicsEnabler=No!!!
Just got lion working but have to boot with GraphicsEnabler=no + flash doesnt work and launchpad flickers
My monitor connection is via VGA as my motherboard does not a direct HDMI output, I have ordered a DVI to HDMI connector so that I can test via DVI to my TV, but not tested this yet.
When I boot with 'GraphicsEnabler=Yes' and verbose mode. I am getting the error:
Sound assertion ""ERROR: EFI ROM did not publish 'hda-gfx' associative property!\n"" failed in AppleHDACodecGeneric at line 331.
I've been looking though lots of similar posts at getting the HD3000 working, but I've not managed to succeed yet. Any help available would be most welcome.
I'd also like to say thanks to all that have contributed to make this work - it very impressive the work and talent that have made this possible.