Search results

I added the "AppleAHCIPort.kext" with KextBeast and rebooted and now my HIGH SIERRA is supporting hot swap add/remove of SATA disks!

Hi SUN1000, (everyone)! I am trying to upgrade from High Sierra to Mojave , using the "Upgrade directly to MacOS Mojave" instructions and I sometimes get stuck on the ' SHIM 2 ', error then the systems reboots. After reboot and I have "dart=0 nv_disable=1 -v" in clover boot options, it will get...

OK guys, UPDATE. I got High Sierra to boot from Disk without UNIBEAST USB. All I did was upgrade Clover to the one from MOJAVE Multi-Beast 11.3.0. I believe it is now CLOVER v2.4k r4934 I had to add "-nv_disable=1" to the clover boot flags, for some reason it was/is missing. So make sure you...

I've not gotten high Sierra to boot directly from disk, I am still booting from UniBeast USB. I will send my config.plist next time I boot.

First time I got this far -supermicro X8DTE motherboard. Catalina, what is this error? Stuck here. Legacy UniBeast.

One other thought, run ESXi 6.7 and virtualize everything. I have done this successfully. Check out book “NetScaler Hacks” on Apple and Amazon.

I have High Sierra running on Supermicro X8DTE with dual E5645. I also can not boot directly from the disk, but need to use the UniBeast USB. But after that H.S. runs smooth. I could Dual Boot as well if I have a separate WIN Disk installed, either by booting directly from the Win disk or...

I would say disable any extra hardware, like serial ports, etc. Disable the PCIe ports too. Make sure they are not set for 'loading/boot PCIe BIOS' or something like that. You are getting further then me with Catalina.

One final tip, I once booted to an older OSX then reboot to Unibeat installer and it worked then. Very strange but that worked for me.

Also I have not been able to get Mojave or Catalina to fully boot on my Supermicro’s yet. Maybe try something older first?

Can you disconnect LAN card? Either that or be sure it is not connected to anything. I never had any problems with built in Intel LAN ports For initial boot.

I don’t know if you resolve this problem it’s from 2012 eight years ago. I’m not sure what the difference is on the various builds between my install of Yosemite, El Capitan , Sierra and high Sierra but ... with my sierra build I am able to hot plug-in hot-swappable drives I have six drivebays...

Ok Good point! I actually tried that. I copied the EFI folder from my unibeast USB drive to the EFI folder on my high sierra hard drive. That also did not work I got the flashing line. I did a replace all, was that a mistake should I have merged ?? I’m just wondering is something unique about...

Is it possible to boot high Sierra with an older version of clover? I tried the “Sierra clover boot loader” from my Sierra multibeast and that also failed. I seem to only be able to boot from USB first only.

Are you installing high Sierra? Remove all PCI cards, except OSX compatible video card . Make sure you use recommended BIOS settings. let me know , tell me more

I have High Sierra running on Similar hardware. Thus far I have not been able to get Mojave or Catalina installed. I’m Using ATI Radeon HD 5870 and it’s butter smooth. Same dual CPU and 48GB ECC Ram . I paid $300 for all my hardware (NetScaler SDX 11500) eBay

OK here’s the latest, one installation of High Sierra is on Intel SSD the second installation is on normal hard drive. SSD has APFS, HD has HFS+ both have multi beast and boot loader legacy installed. Neither one wants to boot directly but both will boot from USB stick first. What else can I...

OK, Not sure WTF was wrong, But I had High Sierra installed on another drive, used the USB stick to boot into the Disk and found no MultiBeast settings (strange). I ran M.B. and rebooted to disk, but stuck on "-". Booted again from USB and ran M.B. again- hope it works now from Disk. I know...

I used the TonyMac install method, to install Yosemite, El Capitan And Sierra successfully in this hardware. Same for High Sierra but after install and running Multi Beast on High Sierra it will not boot. Very strange. Mother board has VT/VT-d disabled and no USB3. Booting from the UniBeast USB...

I have the same problem, did you find a solution?