Recent content by sffjawsh

  1. sffjawsh

    Gigabyte B550 Vision D (Thunderbolt 3) + AMD Ryzen 7 3700X + AMD RX 5600 XT

    @CaseySJ Do eGPUs not work on this motherboard with the flashed TB3 firmware?
  2. sffjawsh

    Gigabyte B550 Vision D (Thunderbolt 3) + AMD Ryzen 7 3700X + AMD RX 5600 XT

    @xtreem.p Does TB3 continue to work after Sleep & Wake for you?
  3. sffjawsh

    Gigabyte B550 Vision D (Thunderbolt 3) + AMD Ryzen 7 3700X + AMD RX 5600 XT

    @CaseySJ Do you know what the command is on Linux? or can you point me to the relevant discussion/website? Thanks! (Have the same ASRock ITX Motherboard on the way for an AMD hack so trying to see if I can do it without using an SPI reader)
  4. sffjawsh

    Gigabyte Z490 Vision D (Thunderbolt 3) + i5-10400 + AMD RX 580

    Just in case anyone's curious, I have the following workarounds in place to tackle the above issues: Allow Bluetooth devices to wake this computer => I had to keep this enabled to ensure I could turn BT ON and OFF after sleep wake cycles I ended up disabling "SSDT-USBW.aml" and...
  5. sffjawsh

    Gigabyte Z490 Vision D (Thunderbolt 3) + i5-10400 + AMD RX 580

    @CaseySJ After a few users posted their TB3 IOReg tree, I checked mine and it wasn't configured correctly. I tried the V2 one and didn't have any luck. What worked for me was the one posted on the HackinDROM website for Z490 Vision D. It has your name on it so I'm assuming you created that one...
  6. sffjawsh

    Thunderbolt 3 ITX Motherboards (+ Hotplug)

    @pi55er5 QQ=> Does TB3 work for you after sleep & wake with that SSDT? Thanks!
  7. sffjawsh

    [Success] ASRock Z390 Phantom Gaming-ITX + TB3 + iGPU + Mojave + SFF Build

    Yes, even with this SSDT, System Report > Thunderbolt still says "No drivers". It shows up in the PCI section. However, sleep does work fwiw => macOS Big Sur 11.0.1
  8. sffjawsh

    [Success] ASRock Z390 Phantom Gaming-ITX + TB3 + iGPU + Mojave + SFF Build

    @mango1122 Thanks! Yes I saw this post here and figured as much. Of course I couldn't leave well enough alone haha! I went to the HackinDROM website and selected ASRock Z370/390. Replaced RP05 w/RP21 for our ASRock Z390 board and, well, here are the results: Cold Boot without Dock connected...
  9. sffjawsh

    Gigabyte Z490 Vision D (Thunderbolt 3) + i5-10400 + AMD RX 580

    @CaseySJ I'm experiencing the following issues with my Youbo WiFi/BT card: After a few sleep & wakes and especially after long ones, I cannot toggle BT anymore. BT still works fine, but if I turn it OFF, I cannot turn it back ON. Apple Watch Unlock doesn't seem to work after sleep & wake...
  10. sffjawsh

    [Success] ASRock Z390 Phantom Gaming-ITX + TB3 + iGPU + Mojave + SFF Build

    Here you go. Let me know if this works.
  11. sffjawsh

    [Success] ASRock Z390 Phantom Gaming-ITX + TB3 + iGPU + Mojave + SFF Build

    @mango1122 and for anyone else trying to get TB3 to work reliably. I saw this post from @CaseySJ here and figured I'd give that SSDT a shot. Switched back to the original (NVM20) firmware using tbpatch and to my surprise, it has been working rather great. I'm testing with an OWC 12-port TB3...
  12. sffjawsh

    Eglobal S200 Nuc Intel i7 8750H / Mini PC Compatible?

    Check if the "usbwakefixup" kext fixes this problem
  13. sffjawsh

    [SUCCESS] Gigabyte Designare Z390 (Thunderbolt 3) + i7-9700K + AMD RX 580

    @dgsga Does TB3 work after sleep & wake? If so, which GPU are you using? Considering this MB but the problem I had with the Z390 ITX was that with the flashed TB firmware, I lost access to TB3 after sleep wake. Tried it with RX 580, Vega 64 & 5700XT - same result.
  14. sffjawsh

    Gigabyte Z490 Vision D (Thunderbolt 3) + i5-10400 + AMD RX 580

    FWIW I experienced the same thing. I saw this post on the forum and was able to get it resolved. I don't know if there are any side effects though.
  15. sffjawsh

    Gigabyte Z490 Vision D (Thunderbolt 3) + i5-10400 + AMD RX 580

    I'm using F_USB 2 and the system is able to sleep and wake without issues
Top