Recent content by LSP

I have MB and CPU as you. Im using Opencore 0.5.8. Trying to get it to work without using Jettison which does work. Memory set to XMP profile 1 in bios. All else works flawlessly. The last piece of the puzzle to solve since its been. bugging me for about a year now. Anythoughts or recommendations

Thanks again esafeddie! Its finally working. I discovered a typo in config. One letter off (fat finger) and once I corrected it all good. Also looking at yours allowed me to tweak mine so its now a little faster on boot

Thank you! Hopefully oit will provide some insight. My board , CPU and System are different (iMac17,1 Z170X and Skylake i7 6700K so some setting including audio not the same.

I’m using official release version 0.5.8 CFG(MSR) is unlocked in the bios via bios hack. NVRAM is native on my board. I would very much appreciate your posting your EFI

I recently added Opencore Gui and Bootchime to my Catalina 10.15.4 build using OpenCore 0.5.8 on Board: Gigabyte Z170X-UD5 TH i7 6700 K Sapphire RX580 8GB Original Apple Extreme on PCi adaptor Samsung 970 500GB After updating settings I reboot and clear NVRAM via the selection in the GUI and I...

You can test for native NVRAM using this NVRAM Testing: You can test if your NVRAM is working by running the following Terminal command and rebooting: sudo nvram TestVar=HelloWorld; once you reboot, run sudo nvram -p | grep 'TestVar'; if you see a result, your NVRAM is working; if not, your...

I use the latest UEFI bios f 22g along with running firmware update tool for thunderbolt support. I did a bios edit to unlock MSR and use NVRAM natively.

It is possible with Clover. There are instructions on how to upgrade the firmware on Gigabyte GA-Z170X-UD5 TH specifically. That has to be done through windows. Follow the info on this post to upgrade the firmware tonymacx86's Skylake Thunderbolt 3 Test Build: GA-Z170X-UD5-TH ... It should work...

My EFI is for Opencore .0.5.7 running Catalina 10.15.4 supplemental on Gigabyte Z170x-UD5 TH

You didn't specify which MB or OS you have and I am running Opencore not Clover. Also please remove any system serials or other specifics info from your plist before posting. If its the hot plug issue I discovered it is unresolvable for my motherboard due to the fact that it not on the XHC...

hanks for the suggestion. Unfortunately it doesn't work. On this board the thunderbolt/USBC are on the pcie bus and are not hot swappable on a real Mac so there is no way to make that happen. It does work if its plugged in at boot but will not reconnect if unplugged

https://khronokernel-2.gitbook.io/opencore-vanilla-desktop-guide/

I Started this project due to the fact that I could not resolve a sleep wake issue that started since I upgraded to Catalina 10.15.4. I previously went through all the guides and created an SSDT for Clover for my USB ports which appeared to have initially caused the problem back in Mojave. That...

I would suggest that you go back to Hackintool and recreate your USB map but use the SSDT it creates along with the SSDT-EC-USBX instead of the USB kext. AlsoSSDT-Plug and SSDT-PMC are missing the extension.aml. SSDT-EC-USBX need to be added to the ACPI folder and added to config.plist

Went back and completely rebuilt my SSDT for USB. All works fine sleep now works ( it seemed mounted USB hard drives cause sleep to fail) With open core I can't see my USB C ports at all where they worked fine in clover. Any thoughts? UPDATE: followed the Vanilla Guide explicitly when setting...