Recent content by bhuether

Hi, I have an RX 48that I use on Mac Ventura. I added Windows SSD and installed blender 4, but realize now that Blender requires an AMD of type Vega or RDNA. I guess CUDA is the typically used method of hardware acceleration in Blender. I suppose that means no AMD cards would support that...

Ok, thanks will check that out

Hi, I am trying to add windows to my existing Ventura internal SSD. That said, if that can impact Ventura performance then I will use a new SSD. For now just trying to use existing drive. I have read this: https://dortania.github.io/OpenCore-Post-Install/multiboot/bootcamp.html#preparations...

Hi, I have Ventura running on a GA Z170Z UD5 board. The board has support for a Gigabyte Alpine Ridge Thunderbolt 3 add on card. The motherboard manual says "THB_C (Thunderbolt™ Add-in Card Connector)This connector is for a GIGABYTE Thunderbolt™ add-in card" And on Gigabyte site regarding the...

As I understood from reading the whatevergreen site " Spoof Skylake as Kaby Lake on macOS 13+ Make sure that WhateverGreen v1.6.0 or above is used. Then, it is necessary to fake device-id and choose an ig-platform-id from Kaby Lake that is closest to the Skylake model (e.g. HD 530 to HD 630)...

Hi, I can't get my VPN working on my Ventura system. It works fine on my MacBook Air with Ventura. I see FastVPN app. On their website they show instructions, and part of it involves allowing keychain access. See attached. But when I install the app I never get these screens, which has me...

I just set up my Ventura system, using symbios iMac 18.3, I have i7-6700k but spoofed to Kabylake. GA Z170X UD5 board. Followed the OpenCore guide and config for Kabylake. Now I am in PostInstall. I am trying to confirm 2 things: 1) that the RX 480 is properly working with all cores and 2)...

Hi, I am up and running with Ventura, but am starting to notice some USB oddities. Some drives not being recognized when plugged into certain ports, for instance. So going through https://dortania.github.io/OpenCore-Post-Install/usb/system-preparation.html#checking-what-renames-you-need But...

Hi, I have Ventura up and running, all seems well. But my WiFI connection is incredibly slow. I am getting about 18 Mbps, while on my Macbook Air I am getting about 270 Mbps. The computers are right next to one another. The Fenzi card has its antennas extended. I see it is receiving at about...

Ok, some final prep questions: 1. I notice instructions mention using HfsPlus but I also see OpenHfsPlus. Just go with HfsPlus? 2. When instructions about network devices talk about "cards" does that also include USB "cards"? In System Report under USB 3.0 I see 802.11ac NIC: Product ID...

Hi, I think I have read relevant instructions, about to make my OC USB installer and gather needed kexts, etc. Have this message from installer creation step: Install media now available at "/Volumes/Install macOS Ventura" Now time to set up the EFI. Just one thing is not very clear...

Hi, yes I have a MacBoor Air M2 with Ventura. On my hack it is currently making the installer, but for quite a while stuck on Copying to disk: 0%... 10%... After this is it recommended to use OpenCore vs Clover?

Ok, I think it is ok now. I ran command as sudo /Applications/Install\ macOS\ Ventura.app/Contents/Resources/createinstallmedia --volume /Volumes/MACVentura /Applications/Install\ macOS\ Ventura.app --nointeraction Previously I was using /Volumes/USB as that is what I saw in the instructions...

I unmounted those disks, but same error.

But in order to complete this command sudo /Applications/Install\ macOS\ Ventura.app/Contents/Resources/createinstallmedia --volume /Volumes/USB /Applications/Install\ macOS\ Ventura.app --nointeraction I need to have the Catalina drive connected. I can't get beyond above step. I have these...