macOS 10.13.6 Update

[Raima]

Hey guys, I ran the update, did the USB3.0 patch and now I get:

USB Accessory Needs Power - Connect "Mass Storage" to a USB port on this Mac.

The USB device I'm plugging in is a 16gb USB3.0 thumb drive

Using a Gigabyte Aorus Z370 Gaming 5.

Any ideas?

 

[rheneas]

Did it not work with the '&'...?

Clover Configurator would not allow me to save config.plist until I removed the ampersand.

 

[narbatucker]

For me, using DP was the issue. Switched to HDMI and rainbow effect went away.

Fixed it for me too, but now I can't daisy-chain my U2515H to my other displays. Most annoying.

 

[IneedMedicine]

Updated through AppStore with no problem. USB 3.0 working.

 

[samireivinen]

Can't complete install. Stucks right away to this text (attached)
What does this mean?

Prior the osx update, I copied the new apfs.efi driver in /EFI/EFI/CLOVER/drivers64UEFI and also updated clover to the latest version. But the update stucked completly. I can't continue even with safe mode. Please help.

 

[vulgo]

For the New USB Raise Port Limit Patch for High Sierra: I edited the Clover config plist with BBEdit as normal, but when I tried to open the plist in the latest Clover Configurator it put up a character error on line 182, and from posts here that's likely the "&." Though properly formatted in BBEdit, the formatting shown in CC was also off. Never saw that before.

It should like this in your editor. & vs &FredWst without closing ;
e.g. PMHeart&FredWst

<key>KernelAndKextPatches</key>
<dict>
    <key>KextsToPatch</key>
    <array>
        <dict>
            <key>Comment</key>
            <string>USB 10.13.6+ by PMHeart &amp; FredWst</string>
            <key>Find</key>
            <data>g32IDw+DpwQAAA==</data>
            <key>MatchOS</key>
            <string>10.13.6</string>
            <key>Name</key>
            <string>com.apple.driver.usb.AppleUSBXHCI</string>
            <key>Replace</key>
            <data>g32ID5CQkJCQkA==</data>
        </dict>
    </array>
</dict>

 

[iDon't]

Lost ALC1220 after this update, reinstalling doesn't helps...(

 

[samireivinen]

Can't complete install. Stucks right away to this text (attached)
What does this mean?

Prior the osx update, I copied the new apfs.efi driver in /EFI/EFI/CLOVER/drivers64UEFI and also updated clover to the latest version. But the update stucked completly. I can't continue even with safe mode. Please help.

Seems the Problem was related with clover bootloader and apfs.efi. I got install done by using USB install drive to start OSX install.

 

[plexi]

It's a problem with the driver and DVI. If you can use a different cable.

HDMI has always looked a little weird on my RX560 but not like this and still usable. DVI always just looked a little sharper.
I've used DVI on that machine ever since and that has now gone shocking pink after the 10.13.6 update.

 

[plexi]

Sad... Here's to hoping this isn't a problem with Mojave. Did you try the "change Board ID to 14,2"?

Not tried that yet? Have you?
I did try both iMac18,3 and iMacPro1,1 with no change.
Even my old P55's running on NVIDIA 9800GT's are fine with update!
Go figure.....