macOS Sierra is Now Available on the Mac App Store

[bss42]

Attach screenshot.

 

[davelaw56]

Updated through AppStore.

I just added kext dev mode and rootless=0 to config.plist. To make sure...
created 10.12 kext folder in EFI/Clover/Kexts
placed Fake SMC, ethernet, and realtek ALC in 10.12 kext folder and "other folder" as well

as expected audio was gone. Clover configurator would not mount EFI so I used EFI mounter v3. First time it would not mount after a first reboot I mounted it but Clover ALC 120 command was not seeing it... So rebooted again, mounted another EFI from another drive, ejected it, then mounted the EFI from the right HDD. Then used Clover ALC 120 command, rebooted and boom audio was back

 

[Quickshooter]

Another weird thing - if i try to mount an EFI partition in Clover Configurator I get "null" and "EFI" folders mounted. The EFI is empty and "null" contains EFI/CLOVER/drivers64UEFI with "CsmVideoDxe-64.efi" and "FSInject-64.efi".

I installed the latest Clover prior to the update.

Everyone else can mount the partition fine?

 

[Quickshooter]

Updated through AppStore.

I just added kext dev mode and rootless=0 to config.plist. To make sure...
created 10.12 kext folder in EFI/Clover/Kexts
placed Fake SMC, ethernet, and realtek ALC in 10.12 kext folder and "other folder" as well

as expected audio was gone. Clover configurator would not mount EFI so I used EFI mounter v3. First time it would not mount after a first reboot I mounted it but Clover ALC 120 command was not seeing it... So rebooted again, mounted another EFI from another drive, ejected it, then mounted the EFI from the right HDD. Then used Clover ALC 120 command, rebooted and boom audio was back

Ah! So here how to mount the EFI thanks!

 

[VioletDragon]

Have you put FakeSMC and appropriate Ethernet kexts in EFI/Clover/kexts/other? how is you're L/E looking?

 

[EddWills95]

You have a very messy L/E folder. You need to clean it up before even attempting to updating. May i ask why you're using TSCSync? and NullCPUPowermanagement? you do not require them when using Z77 chipset. You're board has native Powermanagement.

Truth be told. No idea. Most likely some error came up during something or other and I've just thrown stuff at it to make it work. Which i realise is stupid and irresponsible but my el capitan was pretty solid so I just left it as it was. Learning all the time I guess...

I'll clean it up tomorrow and go from there.
Perhaps it might be an idea to do a fresh install as and when tony etc. finalise UniBeast & MultiBeast as like you say ... its a bit of a mess in there. Ta.

 

[davelaw56]

Ah! So here how to mount the EFI thanks!

Yes I had this problem on last GM too

 

[VioletDragon]

Truth be told. No idea. Most likely some error came up during something or other and I've just thrown stuff at it to make it work. Which i realise is stupid and irresponsible but my el capitan was pretty solid so I just left it as it was. Learning all the time I guess...

I'll clean it up tomorrow and go from there.
Perhaps it might be an idea to do a fresh install as and when tony etc. finalise UniBeast & MultiBeast as like you say ... its a bit of a mess in there. Ta.

Not a good idea to have a messy L/E.

 

[VioletDragon]

Yes I had this problem on last GM too

You can mount EFI via Terminal using
mkdir /Volumes/efi
sudo mount -t msdos /dev/youreidentifiergoes here /Volumes/efi

Example. sudo mount -t msdos /dev/
sudo mount -t msdos /dev/disk0s1 /Volumes/efi

Use su sudo, duskutil list to get identifier.

 

[EddWills95]

Not a good idea to have a messy L/E.

Lesson Learnt