Simple HD 57/58/59xx Installation Using MultiBeast [OLD]

[haribo49]

Re: UPDATED Simple HD 57/58/59xx Installation Using MultiBeast

Appreciate your response!

ty

Hello !
my System is :
GA-P55A-UD3 Rev. 1.0 newest BIOS F11
first GraKa 8800GT, now ATI Sapphire 5770
4 Gig DDR3
Intel Core i3-540
i was running up with the Nvidia 8800GT fine Up to Date an 10.6.6
then i installed per Multibeast the Boot-Driver for the ATI-5770
switched off.... swap the Card (ATI into)
an everything was running again ...so far so good

Now i want to make an fresh Installation with the ATI Card in the System
i followed the Guide from tonymac.....
i started with the newest iBoot-CD 2.6.1...... press F5.....canged the DVD 10.6.0
it hangs at the withe Screen with the "windmühle" spinning and spinning .....
i have tryed -x -v , busratio=23, AtiConfig=Vervet, PCIRootUID=1.... no sucess

what else can i do, to start the Install Prozedure nicely , till the end

Harry

 

[notshy]

Re: UPDATED Simple HD 57/58/59xx Installation Using MultiBeast

Appreciate your response!

ty

Hello !
my System is :
GA-P55A-UD3 Rev. 1.0 newest BIOS F11
first GraKa 8800GT, now ATI Sapphire 5770
4 Gig DDR3
Intel Core i3-540
i was running up with the Nvidia 8800GT fine Up to Date an 10.6.6
then i installed per Multibeast the Boot-Driver for the ATI-5770
switched off.... swap the Card (ATI into)
an everything was running again ...so far so good

Now i want to make an fresh Installation with the ATI Card in the System
i followed the Guide from tonymac.....
i started with the newest iBoot-CD 2.6.1...... press F5.....canged the DVD 10.6.0
it hangs at the withe Screen with the "windmühle" spinning and spinning .....
i have tryed -x -v , busratio=23, AtiConfig=Vervet, PCIRootUID=1.... no sucess

what else can i do, to start the Install Prozedure nicely , till the end

Harry

Try iBoot 2.6.2 - redownload the iBoot.zip file and re-burn it.

Also when you do "-x -v" can you please take a picture of the error message (if there is one) or where it gets stuck.

Thanks

 

[haribo49]

Re: UPDATED Simple HD 57/58/59xx Installation Using MultiBeast

Appreciate your response!

ty

Hello !
my System is :
GA-P55A-UD3 Rev. 1.0 newest BIOS F11
first GraKa 8800GT, now ATI Sapphire 5770
4 Gig DDR3
Intel Core i3-540
i was running up with the Nvidia 8800GT fine Up to Date an 10.6.6
then i installed per Multibeast the Boot-Driver for the ATI-5770
switched off.... swap the Card (ATI into)
an everything was running again ...so far so good

Now i want to make an fresh Installation with the ATI Card in the System
i followed the Guide from tonymac.....
i started with the newest iBoot-CD 2.6.1...... press F5.....canged the DVD 10.6.0
it hangs at the withe Screen with the "windmühle" spinning and spinning .....
i have tryed -x -v , busratio=23, AtiConfig=Vervet, PCIRootUID=1.... no sucess

what else can i do, to start the Install Prozedure nicely , till the end

Harry

Try iBoot 2.6.2 - redownload the iBoot.zip file and re-burn it.

Also when you do "-x -v" can you please take a picture of the error message (if there is one) or where it gets stuck.

Thanks

Thanks a lot for response so quickly

here the picture i have done just now, after i started with the new iBoot-CD 2.6.2

it´s allways at the same Position

 

[notshy]

Re: UPDATED Simple HD 57/58/59xx Installation Using MultiBeast

Thanks a lot for response so quickly

here the picture i have done just now, after i started with the new iBoot-CD 2.6.2

it´s allways at the same Position

Looks more like a disk problem to me - if you swap GFX cards and reboot then can you make it into the OSX Install screen?

What hard drives do you have plugged in when doing this install? What is the chipset of your hard drive controller on your motherboard?

Have you got your BIOS all set to AHCI and HPET 64 bit? Have you removed all other drives and apart from your primary OSX HD and DVD drive? What about removing any excess RAM over 4GB?

 

[haribo49]

Re: UPDATED Simple HD 57/58/59xx Installation Using MultiBeast

Thanks a lot for response so quickly

here the picture i have done just now, after i started with the new iBoot-CD 2.6.2

it´s allways at the same Position

Looks more like a disk problem to me - if you swap GFX cards and reboot then can you make it into the OSX Install screen?

I swaped only the Nvidia 8800GT into, and it runs perfect

What hard drives do you have plugged in when doing this install? What is the chipset of your hard drive controller on your motherboard?
it works perfect with an Nvidia 8800GT, i dont believe its an Harddisk-Problem

only one SATA-Drive Seagate 250gig

Have you got your BIOS all set to AHCI and HPET 64 bit? Have you removed all other drives and apart from your primary OSX HD and DVD drive? What about removing any excess RAM over 4GB?

YES ..YES... only 2 Stripes , a 1GB

funny ... i tryed the same Prozedure with a different Hardware(Machine)
GA-EX58-UD3R, core i7-920 etc....
the same Problem, at this Point, grey Apple-Logo, spinning Wheel

the picture shows the Install-Screen, whit plugged in 8800GT

mmmhhh .... what iam doing wrong

see you tomorrow, i go to sleep now

 

[Utdfan]

Re: UPDATED Simple HD 57/58/59xx Installation Using MultiBeast

try the nawcom boot cd worked for me. was facing the same problem

 

[smooth_opr8r]

Re: UPDATED Simple HD 57/58/59xx Installation Using MultiBeast

@haribo49

Since you got to the install screen with the 8800GT installed, it sounds like the same issue I had. Just install with the 8800GT in the machine, update to 10.6.4 (with graphic update) or 10.6.5 then run Multibeast. After you install Multibeast, shut down and swap cards, then reboot. From there it just a matter of doing some fine tuning.

 

[notshy]

Re: UPDATED Simple HD 57/58/59xx Installation Using MultiBeast

Appreciate your response!

ty

Hello !
my System is :
GA-P55A-UD3 Rev. 1.0 newest BIOS F11
first GraKa 8800GT, now ATI Sapphire 5770
4 Gig DDR3
Intel Core i3-540
i was running up with the Nvidia 8800GT fine Up to Date an 10.6.6
then i installed per Multibeast the Boot-Driver for the ATI-5770
switched off.... swap the Card (ATI into)
an everything was running again ...so far so good

Now i want to make an fresh Installation with the ATI Card in the System
i followed the Guide from tonymac.....
i started with the newest iBoot-CD 2.6.1...... press F5.....canged the DVD 10.6.0
it hangs at the withe Screen with the "windmühle" spinning and spinning .....
i have tryed -x -v , busratio=23, AtiConfig=Vervet, PCIRootUID=1.... no sucess

what else can i do, to start the Install Prozedure nicely , till the end

Harry

Try PCIRootUID=0

 

[big frog]

Re: UPDATED Simple HD 57/58/59xx Installation Using MultiBeast

update for 10.6.6 + multibeast 3.2 = work with 3 monitors display port 1 +dvi + hdmi


thanx

 

[haribo49]

Re: UPDATED Simple HD 57/58/59xx Installation Using MultiBeast

Appreciate your response!

ty

Hello !
my System is :
GA-P55A-UD3 Rev. 1.0 newest BIOS F11
first GraKa 8800GT, now ATI Sapphire 5770
4 Gig DDR3
Intel Core i3-540
i was running up with the Nvidia 8800GT fine Up to Date an 10.6.6
then i installed per Multibeast the Boot-Driver for the ATI-5770
switched off.... swap the Card (ATI into)
an everything was running again ...so far so good

Now i want to make an fresh Installation with the ATI Card in the System
i followed the Guide from tonymac.....
i started with the newest iBoot-CD 2.6.1...... press F5.....canged the DVD 10.6.0
it hangs at the withe Screen with the "windmühle" spinning and spinning .....
i have tryed -x -v , busratio=23, AtiConfig=Vervet, PCIRootUID=1.... no sucess

what else can i do, to start the Install Prozedure nicely , till the end

Harry

Try PCIRootUID=0

OK Sir.....it works for me succesful
tonymac has made a new iBoot-CD (2.6.3) i downloaded, burned, and ....great ....it works also fine, so now i keep my Sapphire, nice Card

tanks at all