Pelase help with Yosemite 10.10 and MultiBeast 7.1.1

[backstreetprod]

Hi all, as you will see I am new on this site and also put together a workstation.
I have follow a post with similar hardware, mine is:


- Micro: Intel Core I7 4790k 4.40ghz 8mb Haswell Socket 1150 Hd
- Mother: 1150 Gigabyte Ga-z97-hd3 Crossfire Sli Hdmi Dvi
- Ram: 1600mhz Kingston Hyper X Fury Ddr3 8gb x 4 (32GB)
- SSD: SanDisk Extrme Pro III 980GB
- Video: HP NVIDIA Quadro K4000
- FireWire PCI


The BIOS version is F6, I follow all the instructions (with the exception that I did not find "Advanced Memory Settings: XMP Profile 1" there´s some ProfileNames)

BIOS SETTINGS:

Load Optimised Defaults
Advanced Memory Settings: XMP Profile 1
VT-d disabled
XHCI Mode Auto
Intel Processor Graphic disabled
XHCI Hand-Off Enabled
EHCI Hand-Off Enabled
SATA Configuration AHCI



The point is that I managed to install and boot the system from the USB without any complication (Recognize the video card, memory, micro, have internet and recognized firewire board) but when I get to the part of MultiBeast and follow the steps of the drivers for this post I complicates everything:


In MultiBeast 7.1.1
Only have Drivers > Audio > Realtek ALCxxx > ALC1150
Drivers > Disk> Intel Generic AHCI SATA
Drivers > Misc > FakeSMC v6.9.1315
Drivers > Misc > FakeSMC v6.9.1315 Plugins
Drivers > Misc > FakeSMC v6.9.1315 HWMonitor Application
Drivers > Misc > USB 3.0 - Universal
Drivers > Network> Intel> AppleIntelE1000e v3.1.0
Drivers > System > AppleRTC Patch for CMOS Reset
Bootloaders > Chimera v4.0.1 (there´s not 3.0.1)
Customize > Boot Options > Basic Boot Options
Customize > Boot Options > Generate CPU States
Customize > Boot Options > Hibernate Mode - Desktop
Customize > Boot Options > Use KernelCache
Customize > System Definitions > Mac Pro > Mac Pro 3,1
Customize > Themes > tonymacx86 Black


The installation completes perfectly fine, but when I boot the system collapses:


Starts to boot and then load the Yosemite, apple apple appears and stays there frozen. No answer anything and I can reset.
Any idea what could be happening? I leave a screenshot of how far I get no problems.




Thank you all for the support!

 

[backstreetprod]

Hi all, as you will see I am new on this site and also put together a workstation.
I have follow a post with similar hardware, mine is:


- Micro: Intel Core I7 4790k 4.40ghz 8mb Haswell Socket 1150 Hd
- Mother: 1150 Gigabyte Ga-z97-hd3 Crossfire Sli Hdmi Dvi
- Ram: 1600mhz Kingston Hyper X Fury Ddr3 8gb x 4 (32GB)
- SSD: SanDisk Extrme Pro III 980GB
- Video: HP NVIDIA Quadro K4000
- FireWire PCI


The BIOS version is F6, I follow all the instructions (with the exception that I did not find "Advanced Memory Settings: XMP Profile 1" there´s some ProfileNames)

BIOS SETTINGS:

Load Optimised Defaults
Advanced Memory Settings: XMP Profile 1
VT-d disabled
XHCI Mode Auto
Intel Processor Graphic disabled
XHCI Hand-Off Enabled
EHCI Hand-Off Enabled
SATA Configuration AHCI



The point is that I managed to install and boot the system from the USB without any complication (Recognize the video card, memory, micro, have internet and recognized firewire board) but when I get to the part of MultiBeast and follow the steps of the drivers for this post I complicates everything:


In MultiBeast 7.1.1
Only have Drivers > Audio > Realtek ALCxxx > ALC1150
Drivers > Disk> Intel Generic AHCI SATA
Drivers > Misc > FakeSMC v6.9.1315
Drivers > Misc > FakeSMC v6.9.1315 Plugins
Drivers > Misc > FakeSMC v6.9.1315 HWMonitor Application
Drivers > Misc > USB 3.0 - Universal
Drivers > Network> Intel> AppleIntelE1000e v3.1.0
Drivers > System > AppleRTC Patch for CMOS Reset
Bootloaders > Chimera v4.0.1 (there´s not 3.0.1)
Customize > Boot Options > Basic Boot Options
Customize > Boot Options > Generate CPU States
Customize > Boot Options > Hibernate Mode - Desktop
Customize > Boot Options > Use KernelCache
Customize > System Definitions > Mac Pro > Mac Pro 3,1
Customize > Themes > tonymacx86 Black


The installation completes perfectly fine, but when I boot the system collapses:


Starts to boot and then load the Yosemite, apple apple appears and stays there frozen. No answer anything and I can reset.
Any idea what could be happening? I leave a screenshot of how far I get no problems.

View attachment 121410


Thank you all for the support!

I found a solution in other Post: http://www.tonymacx86.com/mavericks...osh-doesnt-boot-applekeystore-starting-2.html

Originally Posted by shanike
this is a knows issue with i7 4790k.

Has something to do with the 'generate cpu states' option in multibeast. Temporary workaround is to disable turboboost in bios for this specific cpu.

Works Perfect!!