[PCI configuration begin]

[drm212]

Halt on [PCI configuration begin] can't seem to fix it with anything I've found on here

Hey guys, Im having some problems getting past the PCI config loading Yosemite 10.10.5 with Unibeast 5.2.0.

With these flags -v GraphicsEnabler = no PCIRootUID=1 npci=0x2000

I get a pause on [PCI configuration begin].

I made it past that only once to: RTC: Only single RAM Bank (128) with flags

-v GraphicsEnabler = no PCIRootUID=0 npci=0x2000

Ive been searching around all day, and I think it has something to do with the graphics card drivers that are default in UniBeast? maybe not.

My hardware is:

motherboard = ASUS Z10PE-D16/4L
GPU = GTX 970
RAM = 4x Samsung 8Gb 288pin Registered DDR4

Attached is a screenshot: Any Ideas?

 

[markoco]

I have the same problem with my Gigabyte X58A-UD3R i don't think its a graphics card problem my graphics show up correctly with a vanilla install , here is my configuration

MultiBeast Configuration - 2015-08-30 08:44:37
Quick Start > UserDSDT - /Users/mark/Desktop/MultiBeast - Yosemite
Edition/DSDT-GA-X58A-UD3R-2.0-FH(1).aml
Drivers > Audio > Realtek ALCxxx > ALC889
Drivers > Disk > 3rd Party SATA
Drivers > Misc > FakeSMC v6.16.1372
Drivers > Misc > PS/2 Keyboard/Mice and Trackpads
Drivers > Network > Realtek > RealtekRTL8111 v2.0.0
Drivers > System > AppleRTC Patch for CMOS Reset
Bootloaders > Chimera v4.1.0
Customize > Boot Options > Basic Boot Options
Customize > Boot Options > Generate CPU States
Customize > Boot Options > Hibernate Mode - Desktop
Customize > Boot Options > Kext Dev Mode
Customize > Boot Options > Use KernelCache
Customize > System Definitions > Mac Pro > Mac Pro 3,1
Customize > Themes > tonymacx86 Black

included are screenshots of the 10.10.4 and 10. 10.5 install

 

[Going Bald]

@drm212

The GTX 970 has no native support. Either replace it with a supported card or use nv_disable=1 in your boot-arg string at boot. The disable might or might not work.
You do not need GE=No as this is default in Chimera UniBeast installer

 

[drm212]

I tried All of that and just took the card out and am using the MBs graphics right now.

Everything Ive tried still gets me stuck on:

RTC: Only single RAM Bank (128)

What does this specifically mean?

 

[linuxrox]

@drm212 , are you using Clover or Unibeast ? I have the same CPU as you, i could not get Unibeast to work but got it to boot using Clover. I had to use VoodooTsCsync kext in the Clover USB.

 

[markoco]

Try this in MultiBeast

Drivers > System > AppleACPIPlatform Rollback > 10.9.5 AppleACPIPlatform
Rollback

Bootloaders > Chimera v4.1.0
Customize > Boot Options > 1080p Display Mode
Customize > Boot Options > Basic Boot Options
Customize > Boot Options > Generate CPU States
Customize > Boot Options > Hibernate Mode - Desktop
Customize > Boot Options > IGPEnabler=No
Customize > Boot Options > Instant Menu
Customize > Boot Options > Kext Dev Mode
Customize > Boot Options > Use KernelCache
Customize > System Definitions > Mac Pro > Mac Pro 6,1
Customize > Themes > tonymacx86 Black

Let me know if it works for you

 

[unclejezza]

Hey guys,

I have just had sucess getting past the PCI Configuration Begin problem with this set up.

Solution is here:http://www.tonymacx86.com/yosemite-...aded-pci-configuration-begin.html#post1220077

Good luck!


Jezza.