Gigabyte Z690 Aero G + i5-12600K + AMD RX 6800 XT

[CaseySJ]

Sorry, which post again?

Oops, this one:

Thunderbolt 4 modified firmware with Full Thunderbolt Local Node

Thanks for the input! OK, so I have to get a CH341A programmer. I was researching in other forums to see if someone with the same motherboard had done it previously, but I guess I would be the first! Motherboards can be tricky to work with. It may be best to remove/disconnect all devices before...

www.tonymacx86.com

 

[beelzebozo]

Oops, this one:

Thunderbolt 4 modified firmware with Full Thunderbolt Local Node

Thanks for the input! OK, so I have to get a CH341A programmer. I was researching in other forums to see if someone with the same motherboard had done it previously, but I guess I would be the first! Motherboards can be tricky to work with. It may be best to remove/disconnect all devices before...

www.tonymacx86.com

Thanks for that.

This is what I've implemented-

Renamed device from RP05 to RP09 based on IOREG.

No hot-plug, only cold boot works.

 

[CaseySJ]

Thanks for that.

This is what I've implemented-

Renamed device from RP05 to RP09 based on IOREG.


No hot-plug, only cold boot works.

This is the same behavior I observed on my Gigabyte Z390 Designare. Flashing the firmware enabled Thunderbolt Local Node, but broke sleep. It may be possible to bypass the sleep problem by using the GPRW SSDT and ACPI patch. I’ll get back to this soon.

 

[oldthree]

Will refer to
gigabyte z790m 12600kf rx580

 

[fenky]

@CaseySJ
I fellow the guide to install Monterey(12.7.4) using this EFI file, EFI-077-Z690-AERO-G.zip, but meet errors

My build:
Z690 Aero G
Intel i7-12700K
AMD RX 6800 XT
32GB (2x16GB) ADATA DDR4 3600

BIOS(ver. F6):
Tweaker
Extreme Memory Profile(X.M.P) → disable
Tweaker → Advanced CPU Settings
Option 1: All cores, all threads
Settings → IOPorts
Re-Size BAR Support → disable
All other settings is the same with the guide.

EFI Config(config.plist):
using MacPro7.1


the installing go into the first progress bar screen(p1.jpg), and then stuck into the error page(p2.jpg).

Am i missing something? Any help?

 

[Feartech]

@CaseySJ
I fellow the guide to install Monterey(12.7.4) using this EFI file, EFI-077-Z690-AERO-G.zip, but meet errors

My build:
Z690 Aero G
Intel i7-12700K
AMD RX 6800 XT
32GB (2x16GB) ADATA DDR4 3600

BIOS(ver. F6):
Tweaker
Extreme Memory Profile(X.M.P) → disable
Tweaker → Advanced CPU Settings
Option 1: All cores, all threads
Settings → IOPorts
Re-Size BAR Support → disable
All other settings is the same with the guide.

EFI Config(config.plist):
using MacPro7.1


the installing go into the first progress bar screen(p1.jpg), and then stuck into the error page(p2.jpg).

Am i missing something? Any help?

boot verbose and the take a pic

also don't forget to reset nvram when you make any changes to your EFI/BIOS

 

[fenky]

boot verbose and the take a pic

also don't forget to reset nvram when you make any changes to your EFI/BIOS

thanks for your reply.

the verbose log screen is here:
first, it suck at this log screen(IMG_1.jpg) for while,
then, it go into banned logo screen(IMG_2.jpg).
the log show oddly at banned logo screen(IMG_3.jpg)

any suggestion for a try?

 

[Feartech]

thanks for your reply.

the verbose log screen is here:
first, it suck at this log screen(IMG_1.jpg) for while,
then, it go into banned logo screen(IMG_2.jpg).
the log show oddly at banned logo screen(IMG_3.jpg)

any suggestion for a try?

that usually indicates a USB issue

best to use a USB2 stick for installation, also try all ports on the back of the motherboard

 

[fenky]

that usually indicates a USB issue

best to use a USB2 stick for installation, also try all ports on the back of the motherboard

I using the back USB2.0 ports for a try
first, it stuck at this screen for a while(IMG_1.jpg),
then, the log scroll very fast(IMG_2.jpg)
at last, it get into black screen, and nothing can do at the black screen.

in a short,
if i using the USB3.0 port, it will get into banned logo screen,
if i using the USB2.0 port, it will get into black screen

 

[Feartech]

I using the back USB2.0 ports for a try
first, it stuck at this screen for a while(IMG_1.jpg),
then, the log scroll very fast(IMG_2.jpg)
at last, it get into black screen, and nothing can do at the black screen.

in a short,
if i using the USB3.0 port, it will get into banned logo screen,
if i using the USB2.0 port, it will get into black screen

As per rules, please update your hardware profile to allow others to help you easier

https://www.tonymacx86.com/account/account-details