GA-Z77X-UP5 TH won't start after multibeast DSDT installed

[chat84]

Hi everyone,

Here is my hardware:

MOBO: GA-Z77X-UP5 TH
CPU: Intel i7 3770K
RAM: Corsair Vengeance 1x4gb
SSD: Crucial M4 256gb


The setup went fine until Multibeast. I tried to do it step by step and the problem is when I press the DSDT-Free installation button. From there it won't start and get stucked i the apple logo.

The text I get is the following:


Any of you had the same issue?

Thanks,
Leo

 

[chat84]

I tried to plug my thunderbolt display. It starts if I start with the VGA and the thunderbolt displays and unplug the VGA display at the partition selection page. Kind of weird. Then if I restart with the thunderbolt display it starts only if I put it in verbose mode and then freeze black (the sound is still on through the thunderbolt display...

 

[MiniITX]

Set the BIOS as per here > http://www.tonymacx86.com/99-quick-guide-configuring-uefi-gigabyte-s-7-series-lga-1155-boards.html

Vd-t - Diable

And see if that works.

If the above don't work try booting with -v -f

 

[chat84]

I don't see any VD-t in the bios but Intel Virtualization technology is Disabled.

I tried to follow Alfa's tutorial here: http://www.tonymacx86.com/mountain-...rbolt-updated-10-8-2-multibeast-5-2-a-16.html
but same issue.

-v -f doesn't change anything. I get stuck with this:

 

[Naico]

Try using -v -x -f -F

First I thought that it had something to do with the GraphicsEnabler when I saw your first photo...

Now I believe resetting the BIOS to Optimised Settings will solve the case...

Here are my fail-free settings! (So far)

I managed to get USB 3.0 working before on a previous install, but I'm working on a music project with a deadline right now, so can't experiment before Thursday!

Best of luck!

 

[MiniITX]

Complete a Fresh installation and run multibest with only these options.

DSDT-DSDT Free installation
Audio > Without DSDT > ALLC898
TRIM Enabler > 10.8.1
Network > Intel

And reboot.

 

[chat84]

Complete a Fresh installation and run multibest with only these options.

DSDT-DSDT Free installation
Audio > Without DSDT > ALLC898
TRIM Enabler > 10.8.1
Network > Intel

And reboot.

I tried and got the first freeze:

Try using -v -x -f -F

First I thought that it had something to do with the GraphicsEnabler when I saw your first photo...

Now I believe resetting the BIOS to Optimised Settings will solve the case...

Here are my fail-free settings! (So far)

I managed to get USB 3.0 working before on a previous install, but I'm working on a music project with a deadline right now, so can't experiment before Thursday!

Best of luck!

The above boot arguments didn't make any difference. I will try your multibeast settings but I doubt it will make a difference as the problem seems to be in the DSDT-Free package.

Nevertheless I'm able to boot with GraphicsEnabler=No.

 

[chat84]

I found something here: http://www.tonymacx86.com/multibeas...x-up5-th-i7-3770k-unknown-cpu-model-0x3a.html

There is something wrong with the graphics. I was able to boot through the HDMI port connected to my tv but the resolution was stucked at 1024 as if I was in GraphicsEnabler=No

 

[thepinkbunny]

So you managed to get it to boot after multibeast? I've been having the same problems with the same board/processor. Lmk what you're figuring out. Try as I might I can't make it back in after multi..