- Joined
- Mar 15, 2013
- Messages
- 63
- Motherboard
- Intel NUC DC3217BY M 10.9
- CPU
- i3-7100
- Graphics
- HD 4000
- Mac
- Classic Mac
1. Install OS10.9, Unibeast method
2. Install your wifi and bluetooth kexts
3. Run Multibeast with these settings
- USER DSDT with existing DSDT from Syngates2000Fun thread (see attachment)
View attachment DSDT.aml.7z (or alternative from SenorPixie View attachment 81167)
- enable TRIM support, select AppleIntelPowerManagment.kext and Graphics Enabler
It should look like this in Build:
Quick Start > UserDSDT — /Volumes/Install/Drivers/Sound/DSDT.aml
Drivers > Disk > 3rd Party SAM
Drivers > Disk > TRIM Enabler > 10.9.0 TRIM Patch
Drivers > Misc > FakeSMC vS.3..820
Drivers > System > Patched AppleInteICPUPowerManagement > OS X 10.9.0
Drivers > System > AppleRTC Patch for CMOS Reset
Bootloaders > Chimera v2.2.1
Customize > Boot Options > Basic Boot Options
Customize > Boot Options > Generate CPU States
Customize > Boot Options > GraphicsEnabler Yes
Customize > Boot Options > Hibernate Mode — Desktop
Customize > Boot Options > Use KernelCache
Customize > Boot Options > 1080p Display Mode (native resolution)
Customize > System Definitions > Mac Pro > Mac Pro 3.1 (try 5.1 or 6.2 if you wish)
Customize > Themes > tonymacx.86 Black
4. To enable sound copy and paste these commands into terminal (from Syngates thread too):
Use attached file for copy and paste if posted lines do not work View attachment 79748
It will backup the existing AppleFramebufferCapri to Desktop and modify the installed one to enable sound.
Run these commands again if sound disappears after a system update.
TROUBLESHOOTING
1. The wheel rolls and nothing happens:
- run verbose mode by typing -v during boot and see:
2. If it stops while complaining about CPU
- boot into installer, run Terminal and type in:
- or reinstall from scratch and this time do install the AppleIntelPowerManagement.kext when you run Multibeast.
3. If it stops while complaining about Bluetooth - restart and type ge=yes. Then do select the Graphics Enabler when you run MultiBeast or Chameleon Wizard because apparently you didn't.
4. If it seams video is not working properly, check and see if About this Mac shows 1024Mb of video memory not 512MB. It shows 512Mb if you install an old AppleFramebufferCapri instead of patching current one.
5. Fails to go past the intro after fresh install:
- remove your Bluetooth / WiFi card,
- get past intro and run Multibeast,
- put the card back and try booting again (shiftone).
2. Install your wifi and bluetooth kexts
3. Run Multibeast with these settings
- USER DSDT with existing DSDT from Syngates2000Fun thread (see attachment)
View attachment DSDT.aml.7z (or alternative from SenorPixie View attachment 81167)
- enable TRIM support, select AppleIntelPowerManagment.kext and Graphics Enabler
It should look like this in Build:
Quick Start > UserDSDT — /Volumes/Install/Drivers/Sound/DSDT.aml
Drivers > Disk > 3rd Party SAM
Drivers > Disk > TRIM Enabler > 10.9.0 TRIM Patch
Drivers > Misc > FakeSMC vS.3..820
Drivers > System > Patched AppleInteICPUPowerManagement > OS X 10.9.0
Drivers > System > AppleRTC Patch for CMOS Reset
Bootloaders > Chimera v2.2.1
Customize > Boot Options > Basic Boot Options
Customize > Boot Options > Generate CPU States
Customize > Boot Options > GraphicsEnabler Yes
Customize > Boot Options > Hibernate Mode — Desktop
Customize > Boot Options > Use KernelCache
Customize > Boot Options > 1080p Display Mode (native resolution)
Customize > System Definitions > Mac Pro > Mac Pro 3.1 (try 5.1 or 6.2 if you wish)
Customize > Themes > tonymacx.86 Black
4. To enable sound copy and paste these commands into terminal (from Syngates thread too):
Code:
sudo cp -r /System/Library/Extensions/AppleIntelFramebufferCapri.kext Desktop
sudo perl -pi -e 's|\x00\x00\x00\x00\x00\x02\x05\x00\x00\x00\x04\x00\x00\x07\x01\x00\x00|\x00\x00\x00\x00\x00\x02\x05\x00\x00\x00\x08\x00\x00\x06\x00\x00\x00|g' /System/Library/Extensions/AppleIntelFramebufferCapri.kext/Contents//MacOS/AppleIntelFramebufferCapri
sudo chown -R 0:0 /System/Library/Extensions/AppleIntelFramebufferCapri.kext
sudo chmod -R 755 /System/Library/Extensions/AppleIntelFramebufferCapri.kext
sudo touch /System/Library/Extensions
Use attached file for copy and paste if posted lines do not work View attachment 79748
It will backup the existing AppleFramebufferCapri to Desktop and modify the installed one to enable sound.
Run these commands again if sound disappears after a system update.
TROUBLESHOOTING
1. The wheel rolls and nothing happens:
- run verbose mode by typing -v during boot and see:
2. If it stops while complaining about CPU
- boot into installer, run Terminal and type in:
Code:
cd /
cd volumes
cd [system volume name]
cd system
cd library
cd extensions
mv appleintelcpupowermanagement.kext appleintelcpupowermanagement.old
3. If it stops while complaining about Bluetooth - restart and type ge=yes. Then do select the Graphics Enabler when you run MultiBeast or Chameleon Wizard because apparently you didn't.
4. If it seams video is not working properly, check and see if About this Mac shows 1024Mb of video memory not 512MB. It shows 512Mb if you install an old AppleFramebufferCapri instead of patching current one.
5. Fails to go past the intro after fresh install:
- remove your Bluetooth / WiFi card,
- get past intro and run Multibeast,
- put the card back and try booting again (shiftone).