- Joined
- Nov 24, 2016
- Messages
- 73
- Motherboard
- VN7-791G
- CPU
- i7-4720HQ
- Graphics
- Intel 4600HD
- Mac
- Classic Mac
- Mobile Phone
Dear All.
First of all thank you for a great forum and for any help that you can provide me with.
I have Aspire V Nitro VN7-791G and manage to get Sierra 12.2 boot up and running. Following post will cover how and what I did and what issues I do have now. I intend to create a full guide as seems that VN7-719G is capable to run Sierra.
To be mentioned: those settings could not be switched off in BIOS.
Hyper-V - VM Monitor Mode Extensions Yes
Hyper-V - Second Level Address Translation Extensions Yes
Hyper-V - Virtualization Enabled in Firmware Yes
Hyper-V - Data Execution Protection Yes
Let's start with hardware (with pciID's):
Using a basic guide from https://www.tonymacx86.com/threads/...ierra-on-any-supported-intel-based-pc.200564/ I manage to create a working USB pen (UEFI).
Installer boots, but internal keyboard and touchpad are not functional. Both USB2 and USB3 ports works.
Sierra is installed on SSD with no issue.
Using MultiBeast (Sierra 9.0.1) with following configuration gets system to beet byitself:
After that several kext's are applyed to /L/E:
So what works and how:
What does not work:
I noticed that without "Increase Max Port Limit" set in MultiBeast there will be touchpad but no keyboard available for me. That made me thought that it might be my USB are not configured properly, so playing with that allowed me to have either all USB devices on ECHI (1 or 2 depends on device) or all of them routed through xHCI. This is point No 1 - I can't get devices spread correctly across my USB ports. It will be an issue during Bluetooth subsystem setup as it is routed through USB.
After that I am completely lost under tons of information. I tried several kext and Clover ways to enable DW1560 nic with no success and I got only HDMI audio with no success in enabling ALC283 not to say I had not tried to fix Ethernet so far.
It is almost 5 years that I hackintosh'ed last time and I would appreciate any help. I really can't figure out what should I do, as it seems that some DST patching and Clover insertion is needed in order to get it working as intended.
PS.
There are only 2 threads on tonymacx86 regarding similar laptop:
https://www.tonymacx86.com/threads/acer-aspire-v-nitro-vn7-791g-to-install-el-capitan-os-x.180608/https://www.tonymacx86.com/threads/acer-aspire-v-nitro-vn7-791g-to-install-el-capitan-os-x.180608/
https://www.tonymacx86.com/threads/help-with-dsdt-on-acer-aspire-vn7-791g-yosemite.164649/
First of all thank you for a great forum and for any help that you can provide me with.
I have Aspire V Nitro VN7-791G and manage to get Sierra 12.2 boot up and running. Following post will cover how and what I did and what issues I do have now. I intend to create a full guide as seems that VN7-719G is capable to run Sierra.
To be mentioned: those settings could not be switched off in BIOS.
Hyper-V - VM Monitor Mode Extensions Yes
Hyper-V - Second Level Address Translation Extensions Yes
Hyper-V - Virtualization Enabled in Firmware Yes
Hyper-V - Data Execution Protection Yes
Let's start with hardware (with pciID's):
- Intel Core i7-4720HQ (Haswell with 8 Series/C220 Series Chipset Family LPC Controller 8c40)
- 16 Gb DDR3 PC3-12800
- Nvidia GeForce GTX 960M (Optimus?)
- Intel 4600HD GPU
- 17.3" Full HD (1920 x 1080) 16:9 IPS
- Synaptyc PS\2 touchpad
- PS\2 keyboard with numeric pad (full sized)
- Intel Xeon processor E3-1200 v3/4th Gen Core processor PCI Express x16 Controller 0c01
- So port#3 (8c14) of Intel 8 Series/C220 Series PCI Express Root has:
- > Dell DW-1560 Broadcom BCM94352Z Network Adapter 43b1
- So port#4 (8c16) of Intel 9 Series/C229 Series PCI Express Root has:
- > NetLink BCM57780 Gigabit Ethernet PCIe (Realtek) 1692
- Intel 8 Series/C220 Series USB Contoller ECHI#1 8c26
- Intel 8 Series/C220 Series USB Contoller ECHI#2 8c2d
- Intel USB 3.0 eXtensible Host Controller (B xHCI HC) 8c31
- Intel 8 Series SATA AHCI Controller 8c03 (with port#3 and port#4)
- Intel Management Engine Interface 8c3a
- Intel HM86 LPC Controller 8c49
- Intel 8 Series/C220 Series SMBus Controller - 8c22
- DlueRay MATSHITA BD-MLT UJ272Q (think it's by USB)
- Realtek High Definition Audio ALC283 @ Intel Lynx Point PCH - High Definition Audio Controller [C-2]
- Realtek Semiconductor Corp. RTS5129 Card Reader Controller
- USB powered WebCam (Chicony Electronics Co LTD)
- I have SSD in m.2 slot and hdd attached to SATA controller.
Using a basic guide from https://www.tonymacx86.com/threads/...ierra-on-any-supported-intel-based-pc.200564/ I manage to create a working USB pen (UEFI).
Installer boots, but internal keyboard and touchpad are not functional. Both USB2 and USB3 ports works.
Sierra is installed on SSD with no issue.
Using MultiBeast (Sierra 9.0.1) with following configuration gets system to beet byitself:
- FakeSMC;
- HD 4600 HDMI Audio;
- VoodooHDA 2.8.8;
- 7/8/9 Series USB Support (FakePCIID.kext);
- Increase Max Port Limit;
- MacBook Pro 11,4
After that several kext's are applyed to /L/E:
- RehabMan OS-X-ACPI-Battery-Driver RehabMan-Battery-2016-1118
- RehabMan OS-X-Fake-PCI-ID RehabMan-FakePCIID-2017-0109
- RehabMan OS-X-Voodoo-PS2-Controller RehabMan-Voodoo-2016-1208
So what works and how:
- Internal keyboard works, but ALT and WIN keys are swapped (can be changed in System Settings > Keyboard > Define Keys)
- Touchpad works (System Settings > Touchpad reports that there is no device presented) but double click and drug is very hard to achieved
- WebCamera works
- Seems that applications that require screen to be u[dated frequently generate some issue. Like in the Camera app - some times I get flickering of the image
- Battery get's recognized correctly
- Blue-Ray works out of the box
What does not work:
- Dell DW1560 WiFi card (can't see it on PCI at all)
- CardReader
- Audio (speakers and microphone)
- Bluetooth
- Sleep (only screen goes black with mouse pointer on it
- During Shutdown\reboot screen not always goes black some times leaving desktop with partially visible Dock and round white indicator cycling until system is powered down.
I noticed that without "Increase Max Port Limit" set in MultiBeast there will be touchpad but no keyboard available for me. That made me thought that it might be my USB are not configured properly, so playing with that allowed me to have either all USB devices on ECHI (1 or 2 depends on device) or all of them routed through xHCI. This is point No 1 - I can't get devices spread correctly across my USB ports. It will be an issue during Bluetooth subsystem setup as it is routed through USB.
After that I am completely lost under tons of information. I tried several kext and Clover ways to enable DW1560 nic with no success and I got only HDMI audio with no success in enabling ALC283 not to say I had not tried to fix Ethernet so far.
It is almost 5 years that I hackintosh'ed last time and I would appreciate any help. I really can't figure out what should I do, as it seems that some DST patching and Clover insertion is needed in order to get it working as intended.
PS.
There are only 2 threads on tonymacx86 regarding similar laptop:
https://www.tonymacx86.com/threads/acer-aspire-v-nitro-vn7-791g-to-install-el-capitan-os-x.180608/https://www.tonymacx86.com/threads/acer-aspire-v-nitro-vn7-791g-to-install-el-capitan-os-x.180608/
https://www.tonymacx86.com/threads/help-with-dsdt-on-acer-aspire-vn7-791g-yosemite.164649/
Last edited: